Reply
Posted Jan 10, 2012
2:14:28 PM
Microcell issues

I am on my third Microcell...  ANY suggestions to make this thing work would be great !!  It loses its 3g connection everyday... has to be rebooted... has to sit in a window in order to find its GPS signal,  I am on the fastest internet speed, and been to internet service provider twice to check any problems with internet and there are NONE... Tech's have sent "updates" to my microcell, according to reps on phone, and it will work 4 even up to 5 days at one time with NO issues, then will lose it and here we go again.  Everytime AT&T tells me its a faulty box if it wont "keep" the updates... Three microcells later all with same issue.. not buying it... HELP  we have NO service in our home... Either let us out of contract, or fix it !!!!!!!!!!!!!!!!!!!!!!

14,703 views
80 replies
(0) Me too
(0) Me too
Post reply
Replies
(80)
0
(0)
  • Rate this reply
Sep 27, 2012 9:47:53 PM
0
(0)
Tutor

2 days ago I spoke with Microcell support and as stated Cisco pushed out a new update that once it hits your area we are DOWN. Mine has been down since monday. I have 1 bar signal at home for 2 iphones which actually means text only no call service. I pay extra for the unlimited calls off the microcell and work from home often. This is beyond frustrating 1 day I can understand credit my account and we will move on. But to be down for a week with no forseeable fix? Poor service and support, I am going to demand a substantial credit.

Re: Microcell issues

3,752 views
0
(0)
  • Rate this reply
Sep 28, 2012 5:43:35 AM
0
(0)
Voyager

 

Issue RESOLVED for me.

 

As I mentioned in a previous post, I went to AT&T yeasterday and replaced my microcell with a new one that had not been 'affected' by the firmware update pushed out on 9/17.  Last night I activated the new mcell.  The first time it failed (as usual).   But I deactivated it and reactivated it again.  By this morning, the mcell had successfully activated and my iPhone was connected. 

 

It appears that the new firmware (not the bad one from 9/17), will download and work if the mcell was not affected by the 9/17 download.  But once your mcell receives the bad firmware, it is 'stuck' in that state.   Replacing the mcell was the only thing that helped me.   It is an expensive fix for AT&T.  But, in my opinion, if AT&T can not resolve a problem that THEY caused, they are responsible for replacing hardware to get me working again. 

Re: Microcell issues

3,728 views
0
(0)
  • Rate this reply
Sep 28, 2012 7:08:33 AM
0
(0)
Tutor

It appears that the new firmware (not the bad one from 9/17), will download and work if the mcell was not affected by the 9/17 download.  But once your mcell receives the bad firmware, it is 'stuck' in that state.   Replacing the mcell was the only thing that helped me.   It is an expensive fix for AT&T.  But, in my opinion, if AT&T can not resolve a problem that THEY caused, they are responsible for replacing hardware to get me working again. 


 

Thanks for the update.  The issue is now resolved for me also, with the fix occurring sometime over night.  I still had the flashing green 3G LED as of 11:30p last night, but as of 6:30a the next morning, it was resolved.

 

I didn't replace my unit as you did, so I expect that ATT pushed another firmware update and/or did something else on the back end to resolve the issue.  Two days prior, I did receive a new Mcell under warranty, and this one also showed the "blinking 3G" issue after activating.  So, perhaps new HW isn't required at all, and the timing of events in your case was just a coincidence.  I hope this is the case at least, because it's really inconvient for ATT customers to have to replace their devices to resolve this issue.

 

Short story: For me, the issue was resolved with no apparent action on my part (i.e. replacing the unit, power cycling, etc.).  I did try all of the above in the days prior to the fix, but none had helped the issue.

 

Re: Microcell issues

3,717 views
0
(0)
  • Rate this reply
Sep 28, 2012 8:52:45 AM
0
(0)
Contributor

Miracles do happen.  Mine started working around 3:30AM.

Re: Microcell issues

3,699 views
0
(0)
  • Rate this reply
Sep 28, 2012 2:54:12 PM
0
(0)
Voyager

My situation here in NW La. is a bit different.  LIke others, my unit worked flawlessly for well over a year until we returned from vacation on the 17th to find that our phones would not connect automatically, as they had in the past.  I always have a steady set of lights, not blinking, but I have to reboot my GalaxyS2 in order to connect.  Even then, the signal may drop at any moment.  My wife has a Samsung Solstice, and hers will occasionally connect on its own, drop, reconnect.  I am sure it is not a phone issue; I am an adroid geek, and nothing has changed on the phone.  Rebooting the unit does nothing to resolve the situation.  Am going to research the reset button.  Does this restore the factory defaults??

Re: Microcell issues

3,654 views
0
(0)
  • Rate this reply
Oct 1, 2012 11:48:25 AM
0
(0)
Voyager

My microcell worked for the most part until recently. It just lost internet connectivity. I called supprt 3 different times and each time I was told my unit is old. I need to buy a new one. Great. I pay $100 a year (avg) for the device, $20 a month more to actually use it, and have to replace it every other year? I was a bellsouth mobility customer, then Cingular, then AT&T. I have AT&T for my home, my business that my wife runs, and my full time job. Lets see, that is 5 cell phones, two home phones and two business lines. NONE of my cell phones work at home without the microcell. AT&T is firm about not helping. The sprint rep happeneed to come by and we were taliking and I explained I am under contract so I can't switch. He hooked me up with a FREE Sprint microcell and a Sprint Blackberry at no charge for 6 months. WHY doesn't AT&T care as much about me as Sprint? I know sprint wants my business, but I would think AT&T would want it too. I have been a loyal customer since before my salesperson was BORN! I have several iPhones and a couple of Blackberrys that will be traded in for iPhones asap  I WANT TO STAY WITH AT&T!! Help me out!! I need to be able to USE the phones that I am paying a fortune for. I know the Postal Service just switch THOUSANDS of cell phones and business phones from ATT to Sprint, maybe you guys just need time to recover, but chasing away loyal customers WILL NOT HELP.  I AM BEGGING you to help me stay loyal......Your move.

Re: Microcell issues

3,547 views
0
(0)
  • Rate this reply
Oct 1, 2012 12:47:46 PM
0
(0)
Tutor

I finally got my setup back to normal and 100% operational EXCEPT I still have the 15-20 second delay on outbound calls. ATT said thats normal and not corrective. Anyway, I opened up the ports as noted except I opened the ports for both TCP/UDP and then powered everything down, and then powered them all on. My  router is a Linksys E4200 V2 with the new cisco cloud. It worked this time.

 

Microcell support was too quick to blame the router and actually told me I should replace my router! This was a very bad customer support issue that I had them accountable for by issuing me a credit. I am not switching, I came from Sprint with a 3G home tower also that was disasterous. If I didnt have this call delay I would be 100% satisfied again. All they had to do was shoot us an email or text ( I get ATT text msgs every so often that are annoying ) in advance or once they realized there was a firmware issue. Imagine the non-tech savvy people out there trying to get this fixed.

Re: Microcell issues

3,541 views
0
(0)
  • Rate this reply
Oct 13, 2012 6:47:36 AM
0
(0)
Contributor
Maybe resolved. Sat morning and have left/come back twice and reconnected like it is suppose to. Hope it's fixed.

Re: Microcell issues

3,311 views
0
(0)
  • Rate this reply
Oct 19, 2012 12:34:23 PM
0
(0)
Voyager

I bought a microcell for my Mom's house because she is on my family plan and lives in a metal sided mobile home with extremely weak signal. At the time she was on DSL through Centrylink. The initial setup went as expected and we had GPS signal within the expected 90 minutes. The microcell ran perfectly with all phones until about 8 months later when she switched providers to xfinity (cable modem). The modem she now has is a router/modem, I'm not sure if that's what the problem is or if it's because it's now cable instead of DSL....either way, now we can't even begin to get any connection action what so ever. I have called tech support about this and asked specific questions as to why this could be happening but the man didn't answer my questions, he just insisted that we wait longer to see if it reacts and said they would call me back the next day between 3:00 and 5:00. Well...they did call but they called at 2:21 before I got home. The microcell has been in the window for three days now and still not a sign of anything working other than power and internet. PLEASE help us with this issue. I know the microcell can get the GPS signal as it did before so what I really need is someone to check into the possibility of it maybe not being compatible with the xfinity modem.
I have to add...I have been with AT&T for many, many, years and they have always taken excelent care of me, I'm hoping for the same service now.

Thank you in advance

Connection Speeds ....   Download 18.44 Mbps    Upload 4.88 Mbps

Re: Microcell issues

3,188 views
0
(0)
  • Rate this reply
Oct 19, 2012 12:45:57 PM
0
(0)
Voyager
I'm new here and not yet sure of how to navigate this site. Can you re-post your port settings along with instructions on how to get to the settings. I'm willing to try anything at this point. Would really appreciate any help you can give. Thanks!

Re: Microcell issues

3,184 views
0
(0)
  • Rate this reply
Oct 19, 2012 1:02:35 PM
0
(0)
ACE - Master

Julie_B wrote:
I'm new here and not yet sure of how to navigate this site. Can you re-post your port settings along with instructions on how to get to the settings. I'm willing to try anything at this point. Would really appreciate any help you can give. Thanks!

I posted the link to the MicroCell Troubleshooing Guide which has instructions for setting up port forwarding for various routers. It should be made a sticky soon so it will be at the top of the page.

 

http://www.wireless.att.com/media/en_US/swf/3Gmicrocell/ATT3GMicroCell-Troubleshooting.pdf

 

 

___________________________________________________________

3G MicroCell Technical Guide by Otto Pylot


I am not an AT&T employee. For additional help, please send a PM to ATTCustomerCare

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Microcell issues

3,174 views
0
(0)
  • Rate this reply
Oct 20, 2012 7:02:23 PM
0
(0)
Voyager

Otto Pylot wrote:

Julie_B wrote:
I'm new here and not yet sure of how to navigate this site. Can you re-post your port settings along with instructions on how to get to the settings. I'm willing to try anything at this point. Would really appreciate any help you can give. Thanks!

I posted the link to the MicroCell Troubleshooing Guide which has instructions for setting up port forwarding for various routers. It should be made a sticky soon so it will be at the top of the page.

 

http://www.wireless.att.com/media/en_US/swf/3Gmicrocell/ATT3GMicroCell-Troubleshooting.pdf

 

 


Thank you so much for your help...I'll give it a try!
Love the microcell and really hoping this will get it back up and running.

Re: Microcell issues

3,130 views
0
(0)
  • Rate this reply
Nov 9, 2012 11:53:02 AM
0
(0)
Tutor

I purchased a microcell about three months ago and it has been performing well but yesterday it started dropping the connection. I did the power recycle and it came back late last night and was on for a short while this morning but has since dropped the connection again. I did another power recycle but it has not connected again. The only thing changed was I added my new iPhone5 to the microcell a few days ago or rather a technician with AT&T did this for me. So now my Iphone and my husband's iPhone are on the microcell.

 

I have zero service at my home without the microcell, so what is the solution? I don't feel I should have to purchase another $200 tower after only having this one for such a short time. Thanks.

 

 

Re: Microcell issues

2,806 views
0
(0)
  • Rate this reply
Nov 9, 2012 12:06:23 PM
0
(0)
ACE - Master

If you purchased your MicroCell new only 3 months ago then you are still under warranty. If support can't get it working for you, then they should replace it under warranty if they think it's a faulty MicroCell. Are both iPhones unable to connect now or is it just the iPhone 5? There was a firmware push a month or so ago for the new 4G service that iPhone 5s can do and there have been issues with that. You may want to try and de-register/re-register the MicroCell because some have reported that doing that corrected the problem with iPhone 5 connectivity.

___________________________________________________________

3G MicroCell Technical Guide by Otto Pylot


I am not an AT&T employee. For additional help, please send a PM to ATTCustomerCare

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Microcell issues

2,800 views
0
(0)
  • Rate this reply
Nov 9, 2012 12:15:47 PM
0
(0)
Tutor

The MicroCell will not hold a connection so nothing connects.  The five bars on the front of the cell tower just blink.  When it actually holds a connection my phone has no problem connecting but the microcell itself won't connect.

Re: Microcell issues

2,795 views
0
(0)
  • Rate this reply
Nov 9, 2012 12:16:50 PM
0
(0)
Tutor

One other thing, how do I get in touch with support?  I can't seem to find that anywhere and that is why I posted here.

Re: Microcell issues

2,795 views
0
(0)
  • Rate this reply
Nov 9, 2012 2:56:19 PM
0
(0)
ACE - Master
Edited by OttoPylot on Nov 9, 2012 at 2:58:25 PM

maggiebur wrote:

One other thing, how do I get in touch with support?  I can't seem to find that anywhere and that is why I posted here.


PM support. Go to the blue envelope in the upper right hand corner of this page, click on it and then click on Compose New Message. Send to ATTCustomerSupport. Give them as much info as you can about your problem, setup, phones, etc. I think they are there from 8-5 CST M-F.

 

___________________________________________________________

3G MicroCell Technical Guide by Otto Pylot


I am not an AT&T employee. For additional help, please send a PM to ATTCustomerCare

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Microcell issues

[ Edited ]
2,782 views
0
(0)
  • Rate this reply
Nov 11, 2012 9:16:05 AM
0
(0)
Tutor

Anybody actually know the address to which a message should be sent?  That one does not work.

Re: Microcell issues

2,702 views
0
(0)
  • Rate this reply
Nov 15, 2012 3:49:32 AM
0
(0)
Tutor
Edited by comintel on Nov 15, 2012 at 4:00:23 AM

The following worked for me:

 

(1) Make sure it is near a Window and leave it there

(2) Plug your computer into the Microcell - not separately to the router.  This will rule out one class of problem by allowing you to easily confirm that you do not have cable or ISP problems. (If the computer can access the Internet configured this way, so too should the Microcell itself be able to).

(3) Hard reset the Microcell by holding in the recessed button on the back with a pin until the bottom light starts flickering.   The let everything complete - may take 20 minutes.  WARNING: This is not an AT&T recommended step and could "brick" (permanently damage) some Microcells with a hardware defect according to some reports some time ago and I cannot be responsible if this happens to any Microcell, old or new.

 

 

 

 

Re: Microcell issues

[ Edited ]
2,476 views
0
(0)
  • Rate this reply
Nov 15, 2012 9:05:04 AM
0
(0)
ACE - Master

maggiebur wrote:

Anybody actually know the address to which a message should be sent?  That one does not work.


You are correct. I just tried it myself. Let me see if I can find out what's happening and I'll get back to you.

 

___________________________________________________________

3G MicroCell Technical Guide by Otto Pylot


I am not an AT&T employee. For additional help, please send a PM to ATTCustomerCare

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Microcell issues

2,448 views
0
(0)
  • Rate this reply
Nov 15, 2012 9:34:09 AM
0
(0)
ACE - Master

maggiebur wrote:

Anybody actually know the address to which a message should be sent?  That one does not work.


The correct address is: ATTCustomerCare. Sorry about that :smileyembarrassed: I had support on my mind and replaced Care with Support when I posted. I sent you a pm with the correct address as well. I sent two test messages and they both went thru ok.

 

___________________________________________________________

3G MicroCell Technical Guide by Otto Pylot


I am not an AT&T employee. For additional help, please send a PM to ATTCustomerCare

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Microcell issues

2,437 views
0
(0)
  • Rate this reply
Aug 26, 2013 9:50:02 AM
0
(0)
Contributor

I registered here just to briefly let anyone know what solved my Microcell problems - same as most of you, unit having to be reset on a daily basis.

 

I have mine is my recording studio - a while back I did a little rewiring the upshot of which was I was able to power the microcell from my Uninterruptable Power Supply (UPS). Previously it had been considered "non-essential" and was just powered off the regular house main power.

 

Bam - 3 months now without a single reset needed. In my case at lleast it was simply a question of the quality of elecrical power and/or the Microcell's inability to handle all but pristine electricity.

 

Hope this helps some of ypou.

Re: Microcell issues

1,015 views
0
(0)
  • Rate this reply
Aug 26, 2013 10:54:33 AM
0
(0)
ACE - Master

Using a UPS is always a good idea, especially if you have, or suspect, power issues. I use an APC BE 550G for my MicroCell, router, and DSL gateway. The MicroCell seems to be particularly sensitive at times to fluctuations in power. We've been doing some remodeling lately and have had the power go off and on for a couple of days while re-wiring was done. The Microcell always came backup within about 8 minutes if the power outage lasted longer than the battery backup. Never any call or connection issues.

___________________________________________________________

3G MicroCell Technical Guide by Otto Pylot


I am not an AT&T employee. For additional help, please send a PM to ATTCustomerCare

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Microcell issues

1,003 views
0
(0)
  • Rate this reply
Dec 1, 2013 6:54:48 AM
0
(0)
Tutor

Not sure if this topic is still active, but I'm having similar problems with my Microcell.  I've had the Microcell for over 2 years and other then minor outages, I've had great service.  About 2 months ago it started giving me issues, first, for most of the day, and now mainly at night, after 1 in the morning.  In the beginning the tech was finding the "Handout" to be activated, even if it was De-activated it would reactive itself.  Now it's just not giving a signal after about 1 in the morning like the Handout is reactivated but its still showing "De-activated", and my phone searches for and outside tower, which is to far away to give me a working signal, and of course the fun part is about 7am it goes back on and works perfectly as it is now.  Yes, I have gotten a new phone since this started and already returned it to AT&T not to get locked in under a new contract if my only solution is to move to Verizon, they have great service hear, as it use to be, back when it was Singular.  I've also had my internet service check and a new modem installed.  I believe AT&T has done up-grades and it affected my Microcell in a non positive way.  I have received Text message "In Spanish and I'm not and don't speak it" in the past telling me that work is in progress to fix problems with the Microcell, but to date, I can't get anyone at AT&T to update me on what the status is.  Anyone having similar problems or suggestion other then moving to Verizon would be greatlly appericated, Thanks

Re: Microcell issues

694 views
0
(0)
  • Rate this reply
Dec 1, 2013 7:21:14 AM
0
(0)
Mentor
What model is your Microcell? The latest is DPH153-AT. There are many for sale on eBay, but most seem to be model DPH151-AT. You know that the upfront cost of switching carriers can be steep (new phones, activation fees, first month in advance, etc.) There are some DPH153-AT models on eBay, usually in the $100 to $150 price range, occasionally you can find one just below $100. Would it be worthwhile to get a new model vs. chasing your tail trying to fix an outdated one?

Re: Microcell issues

688 views
0
(0)
  • Rate this reply
Dec 1, 2013 8:09:27 AM
0
(0)
Tutor

Thanks for responding, I have to first start by address the cost statement.  I feel that it's a lot more costly to pay a premium price for poor service or sometimes service.  If I'm willing to settle for that I should go to a Discount provider, to save money.  

On the model, yes, I have the older model 151, but old or new, AT&T has checked, and claims it's working perfectly.  Also works perfect most of the day, just looked at it, and it's fine.  But why at around 1 in the morning does the phone search for and outside tower, even if I reset the unit and it goes back to the Microcell, minutes later it again searches for and outside tower.  Also the first month this started happening, the AT&T service rep would find the Hand-out to be activated, and would De-activate it, only to find minutes later it would re-activate again.  I have been notified through AT&T in the past, that they are still addressing problems with the Microcell (in Spanish of course, have to call AT&T to find out what it says) and I feel what they may have come up with as a Fix, is now what's causing my problems, or of something to do with the new 4G network that is going in in my area.  But what ever it is, it seems to be in their program that causes my phone to stop using the Microcell and search for and outside Tower.  

Appreciate you taking the time to talk about it, always good to get other opinions. 

Re: Microcell issues

679 views
0
(0)
  • Rate this reply
Dec 1, 2013 9:11:19 AM
0
(0)
ACE - Master

What does the light pattern on the front of the MicroCell indicate? Do you ever see the 3G light blinking green or red, or anyother light? Does your phone indicate "M-Cell" at the top or do you just see the reception signal bars?

 

If your MicroCell is restarting itself, that forces it to go thru the Activation process which in turns resets to its default status of which Handing Off is one.

 

When there are updates or maintenance issues done by AT&T, those usually are done during the times of least cell acitivity for you area which is in the early morning hours. If AT&T is indeed updgrading your area to 4G, they may be doing some work on the towers and temporarily shutdown the MicroCell Service Area, which will cause your unit to restart and re- Activate. 4G has no effect on the MicroCell other than upgrading the towers because the MicroCell will only connect at 3G.

 

Something could have happened to your account if you are receiving messages in Spanish because I've never heard of that. I'd PM CustomerCare (link is in my sig) with your issues, account information, what has been done, and your location.

 

The model number of the MicroCell may or may not have something to do with your problem. I'm still using one of the first released MicroCells and it has been solid as a rock for the last few years. Buying off of eBay is always a chance because you don't know if the MicroCell has been correctly deactivated by the original owner or if it is damaged in some way. MicroCell's can't be fixed so you need to be careful.

 

Check the ac adapter and see if it is hot to the touch. It should feel about as warm as the top of the MicroCell does where the circulation vents are. If the adapter feels too warm (subjective), then it could be a failing power supply causing the MicroCell to restart. Make sure there is plenty of ventilation around the adpater and the MicroCell.

 

The communication between the MicroCell and your cell phone is a constant one while the phone is turned on. Signal strength is critical and if the signal drops below a certain level by either the MicroCell or the phone, the phone will start looking for a stronger signal. There could be something in your area, in your home, in your setup that causes this. Maybe your ISP is doing maintenance and there's a temporary loss of connectivity to the AT&T servers causing a reboot. I'm assuming that the setup hasn't been changed and it correct.

 

You might want to try a hard reset (holding in the reset button on the back for about 30 seconds). That completely erases the MicroCell settings and causes it to go thru the entire Initial Activation process (see link in my sig to the Guide for detailed information). There may be something in the registers that is not right so resetting may clear it.

___________________________________________________________

3G MicroCell Technical Guide by Otto Pylot


I am not an AT&T employee. For additional help, please send a PM to ATTCustomerCare

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Microcell issues

675 views
0
(0)
  • Rate this reply
Dec 1, 2013 10:30:42 AM
0
(0)
Tutor

Not sure which is the 3G light, but normally it maintenance the standard Green light pattern that it's had since I installed, top 3 lights on, the forth light off, but, looking at it closely, it does have a slight Green blink.  Then the Fifth or bottom light is a solid Green.  Only when the unit goes down for other reasons do I see a Red light.  With all the problems, it still maintenance the standard Green light pattern indicating it's working, weather the phone is connecting or not.

The Phone right now is reading AT&T MicroCell and is working perfectly.

I've never seen the Microcell Restart itself unless done when working with and AT&T rep.

I understand that the updates and maintenance is done at night, when I seem to be having these problem, but AT&T does not seem to know that anything is being done and since it's happening every night, I think we should be notified.  I work at night and this has really effected my business.

I have been contacting AT&T about all the problems, including the Spanish Texts.  But I find 4 out of 5 of their Phone advisor, have no idea of what their talking about, and sometimes you consider yourself lucky to understand what their saying, because their not always speaking a language you can understand easily.

Yes their is work going on in my area and I'm also friends with one of the engineers.  But he tells me on some of my phone problems with AT&T, his father matches me, could be we're just to old to adapt.  But I've had a lot of my problems happen when I'm on the phone with AT&T, so they know they do exist.

Also the Microcell is at what feels like a good operating temperature and so is the Power Pack.

I fought with Comcast for about a year, on what I felt was a low power signal strength, they said it couldn't be and I had a strong signal.  They finally broke down and sent a someone out, he informed me I had less then a 20% signal entering my Condo and found the same on the whole complex.  I now have no problems, took less then a half hour to fix.

I found if you fight with them enough they finally fix the problem, the question is how much longer I'm willing to put up with AT&T, or bite the bullet and move to Verizon.  I've had and AT&T cell phone service since 94 and don't really like changing, but their pushing, wish it was still Singular, didn't need a Microcell.

Re: Microcell issues

668 views
0
(0)
  • Rate this reply
Dec 1, 2013 12:18:32 PM
0
(0)
ACE - Master

The nominal working light pattern, from top to bottom is:

 

Power, etherent (looks like the world), GPS (looks like a satellite), computer (looks like a computer and should not be lit at all), and then 3G (which looks like signal bars). All of those light should be a solid green all of the time, whether you are using your phone or not. A blinking green 3G light means you have lost connection to the AT&T servers, a blinking green GPS means you have lost satellite lock (which is essential for the MicroCell to work properly), and a blinking green ethernet light means you have lost ethernet connection to your router/gateway.

 

There is now only one Customer Support division that handles the MicroCell and that is located stateside somewhere (I don't remember the exact state right now). Nothing is farmed out overseas.

 

If you live in a condo, do you have one ISP that provides service to the entire complex (Comcast?). You internet speeds may be fine but any line noise, taps, etc can affect VOIP. That's especially a problem in large complexes that have a central cable distribution box because the more lines you add, or the more the box is worked on, the more apt you are to develop issues. Adaptability has nothing to do with it unless your central exchange area for the condo is old and hasn't been properly upgraded/maintained by your ISP.

 

AT&T can determine if you live in a MicroCell Service Area but basically if your MicroCell works, you are in a Service Area. The rest is determined, for the most part, by the quality of your line back to the ISP and then to AT&T's servers.

 

When our cell service was with Cingular, we had the same poor reception issues that we had with PacBell and now AT&T. Towers are now shared quite often with other providers, especially with 4G/LTE being deployed so that may be why reception/coverage is now an issue for you. Also, new construction (interference), the aiming of the tower beams etc could have changed.

___________________________________________________________

3G MicroCell Technical Guide by Otto Pylot


I am not an AT&T employee. For additional help, please send a PM to ATTCustomerCare

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Microcell issues

656 views
0
(0)
  • Rate this reply
Dec 1, 2013 1:09:58 PM
0
(0)
Tutor

Interesting, lots of little things, but the one thing that makes me question all, is the fact it's now OK during the day time, but turned off at night.  Even if I restart everything I get the Microcell signal on the phone, till I get or make my first phone call and then I loose my signal.  Also it comes right back on again around 7am and normally no more problems till about 1 in the morning.

Looking at the Microcell, what is the Forth light down, the one that looks like a computer?  It seems to have a small blink in the bottom part that looks like it would be the key board?  Could be something I'm seeing from one of the other lights too.

Just for small talk, when I was with the original AT&T, I had a poor signal at my condo, had to walk out in the parking lot to make a decent call.  When Singular took over the signal went up to between 3 and 5 bars.  When the New AT&T came in I dropped to a high of 2 bars to a low of no bars, not even the AT&T logo.  Something had to change in my area, I know just before I was talked into getting the Microcell a new tower was scheduled to be built about 3 miles from me, now no one knows anything about it.  That's the type of things that make you mad, and when someone with a Verizon phone is in my house they have a strong signal, like I use to.  Just in closing, I also notice that when I lost all signal and I'd get a message saying this phone is only for emergency, I'd have 5 solid bars??????

Re: Microcell issues

653 views
Share this post
Share this post