08-07-2013 9:09 AM
Johnie, or anyone. I'm new to this community and would like to have a AT&T remote control the volume on my Denon 1612.
I have a S10-S3 I have used all the codes on the remote codes card provided by AT&T. I can turn off and on my AVR 1612 using 5 of Denon
codes on the card. However I can't control the volume. My old providers Dish and Cox had the code to make their remotes work the volume on my Denon 1612. It's been 2 weeks I'm using 2 remotes you know that blows to have to have 2 remotes to control the sound.
I used every code on remote control program card and I can only turn the Denon off and on. I want to control the volume. I appreciate anyone that can figure this out. Is the silver remote different?
Solved by: Go to Solution.
01-11-2014 9:16 AM
08-13-2013 2:48 PM
Thanks again David
Logitech programming remote on line looks like the way to go. I will have one remote according to beebeesa that will control volume of Denon. Harmony will control DVR FF and jump on DVR correct? Is that what you are calling STB? The STB's are the DVR AT&T box? I guess I could always buy then return if it doesn't do what I want. This is still frustrating that the AT&T remote will not control volume on Denon 1612. Like I said at beginning of this is AT&T needs to make the remote work. Dish and Cox do! I like U Verse so far. Crazy remote thing and buying a super Logitech remote that looks very cool still a bit discouraging if you know what I mean. Thanks again to everyone in this thread
Hope this helps out others.
08-14-2013 4:06 PM
01-11-2014 9:03 AM
My black S10 will bring up the denon AVR 991 remote commands on my tv screen, but the S10 volume rocker switch has no impact on volume. I have used the advanced feature setup of the S10 to send the volume control to the receiver and not the default tv setting, but I get no volume adjustment.
It appears to be only the volume I can't control.
01-11-2014 9:16 AM
01-11-2014 2:03 PM
Success! You were right. I had to try a bunch of codes provided by the manual setup thru the uverse program remote screen. Finally found one that works the volume.
Thanks for your help.
After two years of two remotes, just using one is awesome!
01-11-2014 3:05 PM
01-16-2014 3:22 PM
I am having the exact same issue. I have tried all the codes for my Denon AVR 591, and all of them allow to turn the power on and off to the AVR but none of them allow my to control the volume on the AVR, it just controls the vol on the TV. WHat code did you use? Suggestions. Thanks.
01-16-2014 3:36 PM
01-16-2014 4:20 PM
cpd5215 - It may not be the code for the Denon. There is a basic remote function to program before you can find out about the Denon code. The default is for the remote to ALWAYS control the TV. To change this -
att/ok (simultaneously) - 955 - enter (bottom right)
Then the volume will follow the mode button. See if it controls the Denon.
If it does not or you do not want to change modes to change volume, you can set the U-verse STB volume to 15. Then set the TV and Denon volume to comfortable levels. You can then watch U-verse TV in the att mode & vary the volume using either the TV or the Denon to provide audio.
If you ALWAYS use the Denon & you have a code that controls volume you can insert aux between 955 & enter toALWAYS control the Denon.
Thanks alot. Your suggestion "att/ok (simultaneously) - 955 - enter (bottom right)" worked perfectly!!
Getting U-verse? Great! Welcome to the family! Check out our articles below regarding your Install, Your Appointment, Bill, and other features!