01-03-2010 4:45 PM
I have the Vizio VSB210WS Sound Bar and I was hoping to sync the remotes, so I don't have to use the Vizio remote just for the volume, but I haven't been able to do so.
Has anyone else had success doing this with a Vizio soundbar????
Solved! Go to Solution.
01-03-2010 4:48 PM
The following remote codes are for Vizio TVs, but one of them may work with your Sound Bar:
1343, 1018, 1004, 0178, 0502, 0627, 1756, 1758, 0128, 0117, 1017, 1078, 0030, 0056
05-15-2010 1:30 PM
I am not the original poster, but I have the Vizio VSB210WS sound bar and I was able to get my U-verse remote to control the sound bar using the remote's "automatic search" facility described in the following document:
I used the "home theater in a box" option in step 6.
If I knew how to interrogate the remote to tell you what code the search facility selected, I would.
05-21-2010 8:50 PM
Yes, this works! Open the PDF link and follow the steps in Section B - Using the Automatic Search. It took a little bit before it found the code but I had TV on so I could tell when the sound went off. I kept pushing the Play button instead of holding it down not sure if that matters. Thanks anotherlogin!
07-30-2011 12:53 PM
Hey, this code wont work with my VHT210 sound bar. According to manuel, the 4 digit code is 1517.
Auto find wont work either. Anyone have any suggestions? Need help despartely !
07-30-2011 9:35 PM
after lots of research this is what I found, and it worked for me.
Enter the code 4020 Manually. Now after doing this you cannot control the volume, but if you do the step for always sending volume or channel commands to one device then it will work when you select aux.
Hope that helps.
01-08-2012 7:00 AM
We've tried all of the codes in this post so far and can't get the Vizio MODEL NUMBER: VSB210WS to power on or off.
We did however get the volume control to work by setting the default audio level from the U-verse box by programming ATT key. Anyone have an additional key?
01-08-2012 8:34 AM
05-04-2012 5:14 PM
After google'ing and following all of these steps - TO NO AVAIL - I finally figured it out!
Here is what I did, step by step, and it worked... I almost fell to the floor in disbelief
Then, after you get the remote to recognize the sound bar you will then have to program the remote to use the AUX (Soundbar) as the main volume control for all of your devises (TV, DVD, Etc.). Here is how I did that:
* Step 1: Press and hold down the "AT&T" button on the U-verse remote. As you are doing this, press the "OK" button. (Yes, the OK button, NOT the Enter button!) Release both buttons at the same time. The remote is ready when the mode buttons flash twice.
* Step 2: Press 955 within 10 seconds. The AT&T mode button will flash twice to indicate that the code has been recognized.
* Step 3: Press the "AUX" button. Watch for the mode button to flash three times confirming volume control assignment.
That's it! Super excited to finally have ONE remote
05-07-2012 7:14 AM
Having service trouble? There is an app for that! Use our troubleshooting tool or text myATT to 8758 to download the app. It is much faster than posting on our forums. You will also find some helpful articles below.
© 2016 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!