01-31-2013 1:37 PM
Anyone else have the problem where the IR remote that comes with the Motorola receiver is very slow to operate the Motorola unit? Channel change is slow, selecting Guide is slow, etc. Even going right up to the receiver with the remote, it can be slow to respond. I understand the IR remote requires line of sight, how much closer does it have to be if I am inches away from the unit with the remote? I am not sure that going with the RF remote would alleviate this, surely other folks have this problem?
Solved by: Go to Solution.
01-31-2013 2:29 PM
01-31-2013 9:30 PM
Whenever I have real slow remote response I install new batteries and it works a whole lot faster.
02-04-2013 12:28 PM
Mine just started acting up in the last couple weeks too. I have a Harmony 900 that I have been using since we got Uverse a couple years ago (cause we initially had problems with the slowness with the original remote signal, probably due to the TV) and put the box in our A/V cabinet with a RF blaster. It had been working great until late last week when all of a sudden it started responding REALLY slow. Like hold down the key I wanted for 2-4 seconds for it to register slow. I tried rebooting the STB and the Router, but it didn't help. My wife unplugged & replugged in the STB and it seemed to work okay again until this last Saturday where it started acting up again...
Not sure what is going on, but it's getting very annoying...
02-05-2013 7:38 AM
Also: IF it seems to happen on most / all of your STBs, then check the capacity of your DVR's hard drive. IF the drive is full, or near full, the DVR cannot respond to the request as reliably, because it's very busy trying to buffer the streams to whichever TBs are active.
If there's also an active recording session, that may add to the issue.
For all but the 100 level subs (that don't have a DVR), the DVR is an active device ... since it has to do the buffering for "trick" features of whole home DVR (RT pause, etc), it has to coordinate with the STB regarding channel changes. If the DVR is swamped, the whole system tends to respond more slowly.
02-05-2013 8:41 AM
I know our DVR is about a little less then half full. And we only use the one STB. We have a second one in our guest room, but it really never gets used. And our slowness happens during recording and non-recording times. Right now it is all the time.
- edited 02-06-2013 7:31 PM
I'm having the same problem. It started about a week ago. The green button responds immediately to my press of the remote button, but the action on the screen is very delayed. My batteries are new and I don't have a heavy load of DVR programs.
I also noticed that my incoming phone calls don't appear on my TV screen anymore, which caused me to look at the menu options - in addition to no longer having the option to route incoming calls through TV screen, there seem to be other changes to some of the menu options. I wonder if there has been a software update that is causing the problems.
02-07-2013 9:04 AM
Change the 4:3 over-ride in the cable box service menu from 480i to 480p. To access the menu leave the tv on and turn off the cable box. hit the menu button on the cable box or cable box remote. Use the arrow keys to navigate and change the setting, hit power twice to save and turn it back to it. While in there make sure the tv type is 16:9 and hdmi.yprpb output is on 1080i
02-07-2013 10:17 AM
- edited 02-07-2013 10:36 AM
I just turned the cable and tv on and pressed the cable box Menu. Then went to Options and pressed "Restart". System asked me to confirm I wanted to restart and I did. The system rebooted ( or something) and the system came back on and said that there was an update for my TV service. It loaded and a few minutes after the TV and system came back on (and I did wait a couple of minutes so all the info including dvr'd programs could reload), I used my remote and it was acting just fine. Response time back to normal. I'm in Northeastern Ohio, so don't know whether it is a nationwide fix.....surprised me.
- edited 02-07-2013 10:39 AM
Sometimes it takes many tries to get it to stay on the screen meaning be patient and keep trying the button every several seconds. I have had to try for several minutes in some cases. The reason it does not show up is because the service menu is displayed in the format you are trying to change. What is the model number of the cable box you have? The newer motorolas with a -2 or P2 at the end of the model have the setting in the regular cable box menu and is called SD format (or SD...something) and will give you the same options allthough what I have found is that those new ones are beiing delivered with the HD mode in 720p (change that to 1080i) and the SD format is in the "off" position. change it to 480p.
02-07-2013 3:46 PM