06-17-2013 2:26 PM - edited 06-17-2013 2:37 PM
Just turned the TV on...was watching it last night. I have the proper HDMI2 input channel selected. DVR light is on. But no signal to watch local stations. There's a message that says:
"No signal. Check the external input or select another input using the INPUT button."
Never seen this before in the past year. I still have internet and phone. What might the problem be? Is there a place to check for outages in my area? Or do I need to recycle power on something?
Update: Oops...just went through "getting out of the car and back in". All Ops Normal. Sorry for the bandwidth!
Solved! Go to Solution.
06-17-2013 2:42 PM
08-20-2013 5:27 PM
I had a similar problem and I tried to play with TV remote's INPUT button too. It worked! The representative I called scheduled a technician visit. Glad I found this forum.
11-11-2013 7:57 PM
Is this a common problem? It seems to occur daily. Not sure this is much better than Time Warner problems.
11-12-2013 4:26 AM
11-13-2013 12:01 PM
I have this problem a lot. I will be in the middle of watching something and suddenly "No Signal".
Sometimes it will happen when the TV first gets turned on, sometimes it will happen if it has been watched, turned off then (as little as 30 seconds) turned on again.
Seems to be no consistancy in this behavior.
To answer the questions above:
If you are saying your TV is reporting no signal, one possibility is it is on the wrong input. Another is the HDMI is not compatible.
What is the model of the TV & how is it connected to the STB? -- Samsung UN46 serieis LED
Does your problem occur on turn-on or while watching? Yes. See above
How is the STB fed - Wireless, COAX or cat5? Not STB, but the DVR, COAX. And - the two STBs never have this problem
Does this happen on all your TVs or just one? Just the one connected to the DVR.
sometimes, just turning the TV off again, waiting 5 minutes then turning it on resolves the issue.
However other times (this is the more frequent resolution) the DVR must be completely recycled.
11-13-2013 12:26 PM
"No Signal" is a message generated by the TV saying that there is nothing it recognizes as a picture on the selected input.
This might mean that the TV has the wrong input selected, or it may mean that the device that is supposed to be sending a video signal isn't, or the cabling system between them is bad.
You skipped the question of how the TV is connected to the DVR. HDMI, Component, Composite? Is it connected directly, or through a switch or some sort of Home Theater receiver?
11-13-2013 12:32 PM
03-07-2014 6:43 AM
I have a Samsung TV that did the same thing. I called Samsung and they are aware about the problem. It should have been fixed so if you have not updated the TV in the last 3 months do so. The work around they gave and it works perfectly is to turn on the cable box first wait about 10 seconds to give the box time to send the signal then turn on the tv. The problem they explained is that when you turn on the tv and it can not find the signal it reports no signal instead of finding the signal when you turn on the box. I have gotten in the habit of turning the box on first. Hope this helps.
Having service trouble? There is an app for that! Use our troubleshooting tool or text myATT to 8758 to download the app on your device.It allows you to troubleshoot in the palm of your hand - quickly and easily!You will also find some helpful articles below.
© 2017 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!