10-23-2013 8:21 AM
So I have a 2wire with wifi turned off and it's hooked to my new AirPort Extreme via cable. The wifi seem to work great ONCE my laptop (macbook) gets an IP, but it taking 2 or 3 minutes for my laptop to grab an IP.
When I open up airport utility on my mac I see my Airport extreme as green, but the 2wire has a amber dot. When I click on the 2wire it says not connected. After a few minutes the 2wire shows a green circle and then my laptop connects.
This happens every day when I get home from work and my laptop is trying to connect to my home wifi. It willalso happen if I close my macbook and try to reconnect after a few hours. Is there something I can do so the 2wire is always onlie with my AE?
10-23-2013 10:17 AM
Here is how to do it from a forum member Somejoe7777:
There is no true bridge mode on the 2Wire routers. However, you can still configure it such that almost all functions of your own router will work properly.
1. Set your router's WAN interface to get an IP address via DHCP. This is required at first so that the 2Wire recognizes your router.
2. Plug your router's WAN interface to one of the 2Wire's LAN interfaces.
3. Restart your router, let it get an IP address via DHCP.
4. Log into the 2Wire router's interface. Go to Settings -> Firewall -> Applications, Pinholes, and DMZ
5. Select your router under section (1).
6. Click the DMZPlus button under section (2).
7. Click the Save button.
8. Restart your router, when it gets an address via DHCP again, it will be the public outside IP address. At this point, you can leave your router in DHCP mode (make sure the firewall on your router allows the DHCP renewal packets, which will occur every 10 minutes), or you can change your router's IP address assignment on the WAN interface to static, and use the same settings it received via DHCP.
9. On the 2Wire router, go to Settings -> Firewall -> Advanced Configuration
10. Uncheck the following: Stealth Mode, Block Ping, Strict UDP Session Control.
11. Check everything under Outbound Protocol Control except NetBIOS.
12. Uncheck NetBIOS under Inbound Protocol Control.
13. Uncheck all the Attack Detection checkboxes (7 of them).
14. Click Save.
Your router should now be able to route as if the 2Wire was a straight bridge, for the most part.
Inbound port 22 might be blocked, and inbound ports 8000-8015 might also be blocked, and there's nothing that can be done about it.
This is how I have my 2Wire configured, and I have a Cisco 2811 behind it doing IPSec, IPv6 tunnels, etc.
Hope this helps. If not post back and we will see what else we can come up with.
"If you find this post helpful and it solved your issue please mark it as a solution. This will help other forum members locate it and will also let everyone know that it corrected your problem. If they have the same issue they will know how to solve theirs"
10-24-2013 10:08 AM
Does your Macbook have any other issues connecting to other network connections?
If not, then hopefully, the information that BeeBeeSA provided resolves the solution. I am pretty sure it will help a lot.
Also, you may want to try to change the DHCP pool in your AirPort Extreme as you may be running into double NATing issues, but that probably should be resolved if you follow BeeBeeSA's instructions.
You still probably want to change the it though. By default, the DHCP pool for the 2wire is 192.168.1.x. You just want to make sure you are not using the same pool in your Airport Extreme.
Also, if the issue is with your MAC, i found this on Apple's support page.
Symptom: After restarting or waking from sleep, my computer might not connect to the Internet
Use these steps if your computer does not automatically connect to your desired Wi-Fi network.
1. Check your TCP/IP settings in the Network pane of the System Preferences. Click the "Renew DHCP lease" button
2. Select the Wi-Fi tab and view your Preferred Networks list.
3. Remove your stored network passwords using the Keychain Access Utility.
4. Restart your computer.
5. Join your Wi-Fi network. You will need to enter your password for your network again if it requires one.
10-26-2013 5:46 PM
Just a side note you can use the WAN port instead of the LAN port on the AEBS connection from the RG 's LAN since it will adapt I have been doing it with my Airport Extreme and Uverse for 5 years trouble free.
This free up a sometimes needed LAN port .
Welcome to the AT&T TV Hub!We have some helpful articles located under TV Hot Topics.On the left you will see DIRECTV and U-verse TV links. Click on those links for more information regarding Apps, Billing, and TV troubleshooting tips.
© 2017 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!