Helpful Links

Remote control is messed up


Remote control is messed up

I bought a new remote control for the uVerse unit in October.  At random times when I fast forward through a recorded show, I get the uVerse On-Demand screen when I release the ff button.  The on-line chat person was useless.  I said I was dissatisfied with the response on the survey when I ended the chat.  Then I got a call from another ATT rep. He said that the fast forward button on the remote control doesn't work when you watch recorded programs. I asked him how I should skip the commercials and he said I couldn't, that I have to watch them. Really? I've been fast forwarding through commercials for years!  Talk about bad customer service! 

Message 1 of 5
ACE - Expert

Re: Remote control is messed up

bbbwmw - Sounds like you are a victim of IR corruption. My FF corrupted to chan up or chan down .

You can see if an outside source is affecting it by building a tent with a blanket and pole from your wrist to the STB so that it is operating in a light free environment. Be sure the TV is outside the tent.

Another thing you can do is cover the IR sensor with a low degree of transparency. The tape specified below should work like magic. It did for me & a few others nice enough to report back.

More -

IR Issues

Going back 5-6 years there are many posts about IR interference. Remedies included taping over the IR sensor, hiding the STB, turning off auto brightness on the TV.

A common fault was the info button press corrupting to an STB mute action. The number of reports of this have totally fallen away. My personal initial primary problem was getting the zero to register. But, one day long ago that just went away.

Niles Audio Corp. makes IR repeaters & has a video on their web site showing the fragility of the IR coding that is used for U-verse & other boxes. They said their new line of repeaters could handle it. Oddly, a U-verse customer posted in this community that they had a NIles install that was not working & after they contacted Niles they did not get any satisfactory resolution.

I came to believe that the IR sensor is too sensitive, That the DVR is worse than other STBs. That command type buttons are worse than the number buttons. That, somehow software updates can make it better or worse, So, it is a moving target. Hard to pin down.

I noticed that the U-verse remote does work better than my Logitech Harmony model 700. I looked at the IR signal through a digital camera. It appeared to me that the Harmony IR signal is stronger than the U-verse remote. This reinforces my theory that the IR sensor is too sensitive.

Recently, my most common problem was FF and Play Buttons often corrupted to chan up and chan down more than six times a night while watching recorded shows, exclusively.

I happened to notice that I had a specific kind of "duct tape" covering the blue light on the STB. Actually, it just looks like duct tape, but is electrical tape available at the Home Depot in the electrical dept. -

This tape has a degree of transparency. I thought I would use it to cover the IR sensor. The remote has never worked better. In over 100 evenings since I applied the tape - watching recordings while FF through the ads - I have not had one chan up - chan down corruption . Previously, there would have been at least 6x100=600 occurrences.

Almost all button presses are accepted & none are changed to a different action.

RF Issues

It should not be a surprise, but it is, that half the problems with the RF remote are IR. I run an STB well hidden for a second TV. I had the IR sensor covered with black tape. I replaced the black tape with the "duct tape" & saw an immediate improvement in response to menu buttons. The number buttons were already good - see below for that solution.

The STB using RF must be hidden due to the dongle conversion of RF to IR. If it is not hidden it is subject to the following problems:

IR corruption - Ironically, the RF remote was often offered as a resolution for IR problems. But, if the STB is not hidden nothing has changed to eliminate theI IR corruption problem. If the corrupting light can be seen by the STB IR sensor it will continue to corrupt the IR signal.

If the STB IR sensor can see IR from another remote, it will respond to it.

If another STB can see the IR generated by the dongle, it will respond to it.

Note that hidden means the IR does not see outside light - If you have an optical repeater(like the Niles mentioned above) it is IR subject to corruption. If you have an IR receiver that produces RF to go through a wall, it is still IR subject to corruption. Any optical link open to the room is still open to IR corruption.

Only if the remote is RF (like the point anywhere remote) transmitted to a well hidden device will it ward off IR corruption. The ultimate solution is a wireless remote app. These are available, but incomplete & other devices do not yet support wireless remote. But, the Buddy TV remote can be used for a u-verse STB.

Previously, I found the RF remote lacking in RF power - in the same room, twelve feet away, hidden only by a thin sheet of cardboard. One method to increase RF power is to hold the remote under your chin while pressing a button - using your head as an antenna.

A better way is this antenna placed in the battery compartment -

With this antenna, the channel numbers are almost always accepted. With the "duct tape" in place, the other buttons work almost every time. The remote now works better than ever.

But, recently, I discovered that weakened batteries triggers poor results due to low power. If the remote starts acting up go for fresh batteries. Before I realized the batteries were low I was getting better RF by holding it against a metal arm of a reading light.

To increase RF sensitivity - Cut off the base and one leg of a wire coat hanger (one piece). Hold the short leg perpendicular to the dongle and wrap the longer end around the dongle a few turns until the two perpendicular ends are about the same length (about 3”). Cut the longer one to the same length as the shorter one.

STB Issues

Once IR and RF issues are resolved, there are timing issues with the STB to contend with. Numbers process fast and Menu items process slow. You need quick, light touch on some numbers to avoid duplicates and a slow, strong press on menu activities. Effort is required to suppress the urge to press again while waiting for a response. It takes concentration to get effective results. Frequently a second press immediately cancels a slow responding first press. Current IR and RF issues amplify the effect of the timing issue.
*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.
Message 2 of 5
ACE - Master

Re: Remote control is messed up

I was having the same problem but it was nothing to do with the remote.  I re-booted the Uverse receiver and DVR and have not had the problem since.


If re-booting the receiver and DVR don't do the trick you can reboot the whole system.


1) Unplug all receivers from power

2) Unplug the AT&T router from power

3) Plug the Router back in and wait for all green lights (Operational)

4) Plug in just the DVR and let it come up so you can see a picture on the TV connected to it

5) Plug in the rest of the recievers.


Check for proper operation.  Post back if you still have the issue.

"If you find this post helpful and it solved your issue please mark it as a solution.  This will help other forum members locate it and will also let everyone know that it corrected your problem. If they have the same issue they will know how to solve theirs"

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.
Message 3 of 5

Re: Remote control is messed up

AT&T called me about the problem and sent me a new remote.  I think the remote had a short.  At the end of its 'life' it started randomly shutting off the TV.

Message 4 of 5
ACE - Expert

Re: Remote control is messed up

bbbwmw - Glad to hear that your problem is resolved.
*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.
Message 5 of 5
Share this topic

Let us help you Give the Gift of AT&T Entertainment this holiday season!

Additional Support