Ask a question

    Reply
    Posted Sep 26, 2010
    4:04:09 PM
    No Coax/HPNA Devices were found

    noob question. the Uverse realtime reports that it cannot find any Coax/HPNA devices. When I click that tab it connects to the NID and shows a busy signal for a few seconds and then comes back with nothing. Below Stats, Interfaces and Coax screenshots. What does that mean? I have two TVs in the house one DVR the other no DVR, both connected via Coax. Shouldn't they show up? Under Interfaces it looks like HPNA/Coax signal is going through the router.  The main reason I am asking is because my TV stalls for a fraction of a second once in a while and I wanted to check the signals. On the other hand, I think it's likely the DVR itself (maybe the hdd), because when I go back on the same channel and play again, the stall is not present. The stream to the DVR was therefore good I think, just not from the DVR to the TV.

    2826iA8F884414AE60FD0

    2828i217C7C81F55C5D7B

    2830i27757B7623D00D13

    No Coax/HPNA Devices were found

    1,141 views
    13 replies
    (0) Me too
    (0) Me too
    Post reply
    View all replies
    (13)
    0
    (0)
    • Rate this reply
    View profile
    Sep 26, 2010 7:35:10 PM
    0
    (0)
    Teacher

    Ok, this is very possible it's just this test in which will not show you the results!!

    Have you tried to Power Cycle your RG, and re-run these tests?

    Otherwise, if you beleive there is an issue with the lines, or the DVR, feel free to call Tech Support, They can def. run the real time tests and get you some REAL results!! Cheers!:robotmad:

    Re: No Coax/HPNA Devices were found

    2 of 14 (1,141 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 26, 2010 7:36:14 PM
    0
    (0)
    Teacher

    TO AVOID THE ANNOYING IVR CALL: 1-800-515-7272 Press 6 for UVERSE!

    Re: No Coax/HPNA Devices were found

    3 of 14 (1,141 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 26, 2010 8:57:43 PM
    0
    (0)
    Mentor

    thanks for your reply. Everything has been power cycled for the umpteenth time, nothing changes to the realtime test. thanks for the call short cut

    Re: No Coax/HPNA Devices were found

    4 of 14 (1,141 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 26, 2010 9:01:37 PM
    0
    (0)
    Teacher

    Np ausgewandert!

     

    Glad to be of help..... maybe some other's can shed some light.... but it is VERY POSSIBLE, this tool just does not provide these results! :smileyhappy:

     

    As I said feel free to call in if issues persist with your system! Glad to be of help! :smileyvery-happy:

    Re: No Coax/HPNA Devices were found

    5 of 14 (1,142 Views)
    Highlighted
    0
    (0)
    • Rate this reply
    View profile
    Sep 26, 2010 10:17:41 PM
    0
    (0)
    Expert

    Yes, if you have any coax-connected equipment, it should show up on the Coax/HPNA tab/screen.

     

    Look at the Channels/Streams tab?  Can you see all devices listed there?

     

     

    Re: No Coax/HPNA Devices were found

    6 of 14 (1,142 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 26, 2010 10:24:57 PM
    0
    (0)
    Mentor

    yep, thanks. I forgot to add that evidence. they both show up. The Coax/HPNA still shows the same message as above.2832i78A43DE66B55AFBA

    Re: No Coax/HPNA Devices were found

    7 of 14 (1,142 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 26, 2010 10:40:19 PM
    0
    (0)
    Expert

    Not ignoring you, just can't see your photo (until the Mod approves it). :smileywink:

     

    You have the 2Wire 3800?

    Re: No Coax/HPNA Devices were found

    8 of 14 (1,142 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 27, 2010 5:25:36 AM
    0
    (0)
    Mentor

    Router: 2Wire i38HG

    NID: 2Wire i3812V

    Re: No Coax/HPNA Devices were found

    9 of 14 (1,142 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 27, 2010 6:28:07 AM
    0
    (0)
    Employee

    Has anything been added or changed recently?

     

    Check your splitters and all of the other coax connections; make sure everything is more than finger tight (just a light tightening with a wrench).

     

    Sent from my phone.
    *I am an AT&T employee and the postings on this site are my own and don’t necessarily represent AT&T’s position, strategies or opinions.

    Re: No Coax/HPNA Devices were found

    10 of 14 (1,142 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 27, 2010 2:00:51 PM
    0
    (0)
    Expert

    ausgewandert,

     

    You have an i3812V + i38HG combo, which is used for a pair bonded installation.  When I added support of this router to U-Verse Realtime, I did not have any example configurations that had coax-connected devices, so I'm fairly sure that what is happening is that U-Verse Realtime is not properly detecting the coax devices.  They are actually connected and present, but UVRT needs a programming update to find them.

     

    Please follow the directions in this post to save some data from your i3812V router.  I will send you my e-mail address in a private message (PM).

     

    Once you've saved the 5 HTML files as directed in that post, zip them up and e-mail them to me.  I will find out what's going on and fix UVRT to detect the coax devices.

     

    Re: No Coax/HPNA Devices were found

    11 of 14 (844 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 27, 2010 2:14:24 PM
    0
    (0)
    Mentor

    yeah, I totally forgot to mention this. apparently we are guinea pigs in Ohio for this. I will follow directions and send you the results. thanks beforehand.

    Re: No Coax/HPNA Devices were found

    12 of 14 (844 Views)
    0
    (0)
    • Rate this reply
    View profile
    Sep 29, 2010 3:12:18 PM
    0
    (0)
    Mentor

    just to complete the stats from the first page I am adding the bitloading page as well. Any input on whether this is good is appreciated. thanks2914i350686560DAADDC1

    Re: No Coax/HPNA Devices were found

    13 of 14 (844 Views)
    0
    (0)
    • Rate this reply
    View profile
    Oct 2, 2010 7:09:08 PM
    0
    (0)
    Teacher

    This INID installation runs on a completely diff. basis then the original setups for U-verse.

    Very possible this is the issue with your tool..... I see no need to worry about the inconsistent result. Especially if it is not service effecting!

    Re: No Coax/HPNA Devices were found

    14 of 14 (844 Views)
    Share this post
    Share this post