Ask a question
Search in U-verse Forums

U-verse Forums

Reply
Posted Oct 2, 2011
7:38:50 PM
View profile
Can I use my own wireless router?

Possibly a pretty basic question, but I'm not sure. The installation tech said that I had to use their router, and installed one of the 2wire ones - a i38HG one. It's fairly slow and poky compared to the one I used to use with comcast internet - a netgear WNDR3400. Is there any way to use the netgear one instead? Can I just switch the network cable from the 2wire to the netgear router and make it work somehow?

Possibly a pretty basic question, but I'm not sure. The installation tech said that I had to use their router, and installed one of the 2wire ones - a i38HG one. It's fairly slow and poky compared to the one I used to use with comcast internet - a netgear WNDR3400. Is there any way to use the netgear one instead? Can I just switch the network cable from the 2wire to the netgear router and make it work somehow?

0
(0)
  • Rate this reply
View profile
Solved
Oct 3, 2011 11:15:11 AM
0
(0)
Expert
The i38HG is not actually the router, it is just a break-out box that supplies 4 Ethernet ports and a wireless access point.

The actual router is the i3812V unit (the iNID), which is outside attached to your house at the phone line entrance.

You can put your own router in the house to replace the i38HG, but you will have to run an Ethernet cable from that location to the i3812V. The i3812V has an Ethernet port in the outside unit that can be used for this. By default, it's not enabled, you will have to turn it on in the router interface:

http://192.168.1.254/xslt?PAGE=C_2_2

You will also need to keep the i38HG around and handy. Since the Ethernet port in the i3812V defaults to disabled, if the outside unit ever loses power or is factory reset, you will need to go back into the web interface to re-enable it. The only way in at that point is through the i38HG.

Once you have enabled the Ethernet port and run your Ethernet cable, set up your own router using the instructions here:

http://forums.att.com/t5/Residential-Gateway/U-verse-for-BUSINESS-2Wire-3600HGV-bridge-mode-or-another-AT-amp/m-p/2723261#M313
Accepted Solution

Can I use my own wireless router?

13,422 views
3 replies
(0) Me too
(0) Me too
Reply
View all replies
(3)
0
(0)
  • Rate this reply
View profile
Oct 3, 2011 10:15:48 AM
0
(0)
Tutor

Uh, no. I didn't look closely enough at the connector - they're not the same. 

 

Ok, next question - is there any possiblity of getting a better router with this uverse system? This one is fabulously unreliable. 

Uh, no. I didn't look closely enough at the connector - they're not the same. 

 

Ok, next question - is there any possiblity of getting a better router with this uverse system? This one is fabulously unreliable. 

Re: Can I use my own wireless router?

2 of 4 (13,390 Views)
Highlighted
0
(0)
  • Rate this reply
View profile
Solved
Oct 3, 2011 11:15:11 AM
0
(0)
Expert
The i38HG is not actually the router, it is just a break-out box that supplies 4 Ethernet ports and a wireless access point.

The actual router is the i3812V unit (the iNID), which is outside attached to your house at the phone line entrance.

You can put your own router in the house to replace the i38HG, but you will have to run an Ethernet cable from that location to the i3812V. The i3812V has an Ethernet port in the outside unit that can be used for this. By default, it's not enabled, you will have to turn it on in the router interface:

http://192.168.1.254/xslt?PAGE=C_2_2

You will also need to keep the i38HG around and handy. Since the Ethernet port in the i3812V defaults to disabled, if the outside unit ever loses power or is factory reset, you will need to go back into the web interface to re-enable it. The only way in at that point is through the i38HG.

Once you have enabled the Ethernet port and run your Ethernet cable, set up your own router using the instructions here:

http://forums.att.com/t5/Residential-Gateway/U-verse-for-BUSINESS-2Wire-3600HGV-bridge-mode-or-anoth...
The i38HG is not actually the router, it is just a break-out box that supplies 4 Ethernet ports and a wireless access point.

The actual router is the i3812V unit (the iNID), which is outside attached to your house at the phone line entrance.

You can put your own router in the house to replace the i38HG, but you will have to run an Ethernet cable from that location to the i3812V. The i3812V has an Ethernet port in the outside unit that can be used for this. By default, it's not enabled, you will have to turn it on in the router interface:

http://192.168.1.254/xslt?PAGE=C_2_2

You will also need to keep the i38HG around and handy. Since the Ethernet port in the i3812V defaults to disabled, if the outside unit ever loses power or is factory reset, you will need to go back into the web interface to re-enable it. The only way in at that point is through the i38HG.

Once you have enabled the Ethernet port and run your Ethernet cable, set up your own router using the instructions here:

http://forums.att.com/t5/Residential-Gateway/U-verse-for-BUSINESS-2Wire-3600HGV-bridge-mode-or-another-AT-amp/m-p/2723261#M313

Re: Can I use my own wireless router?

3 of 4 (13,380 Views)
Solution
0
(0)
  • Rate this reply
View profile
Oct 4, 2011 7:56:58 AM
0
(0)
Tutor

Excellent reply! Just what I wanted to hear! Thanks!

Excellent reply! Just what I wanted to hear! Thanks!

Re: Can I use my own wireless router?

4 of 4 (13,339 Views)
Advanced
You must be signed in to add attachments
Share this post
Share this post