Ask a question
Search in U-verse Forums

U-verse Forums

Reply
Posted Jul 8, 2011
4:27:36 PM
Can't Access Printer From Secondary Router

I have my Brother MFC-420CN printer plugged into the U-Verse 3801HGV RG.  If I connect my computers wirelessly to the RG, I can access my printer with no issues.  However, to slightly improve my wireless speed, I plugged my CradlePoint N router into the RG and connected my computers wirelessly to the CradlePoint router.  Then, I disabled the RG's wireless signal to prevent any interference.  That seemed to be working great until today, I discovered I could not access my printer.  It's not a big deal because I can remove the CradlePoint router, but I would like to keep it if possible.  Is there some setting on the RG I need to change?

I have my Brother MFC-420CN printer plugged into the U-Verse 3801HGV RG.  If I connect my computers wirelessly to the RG, I can access my printer with no issues.  However, to slightly improve my wireless speed, I plugged my CradlePoint N router into the RG and connected my computers wirelessly to the CradlePoint router.  Then, I disabled the RG's wireless signal to prevent any interference.  That seemed to be working great until today, I discovered I could not access my printer.  It's not a big deal because I can remove the CradlePoint router, but I would like to keep it if possible.  Is there some setting on the RG I need to change?

0
(0)
  • Rate this reply
View profile
Solved
Jul 9, 2011 6:42:25 AM
0
(0)
Guru
Edited by jimgfitzgerald on Jul 9, 2011 at 6:43:12 AM

http://forums.att.com/t5/Residential-Gateway/U-verse-for-BUSINESS-2Wire-3600HGV-bridge-mode-or-another-AT-amp/td-p/2707013/page/2

 

See post #13 by SomeJoe7777.  I followed steps 1 and 2.  IP addresses were OK as was.  I also disabled wireless signal from the U-Verse RG.  Everything seems to be working great.  I have all my wired devices connected to the RG and all my wireless devices connected to my CradlePoint N router.  Thanks Joe for all the good information.

Accepted Solution

Can't Access Printer From Secondary Router

1,198 views
3 replies
(1) Me too
(1) Me too
Reply
View all replies
(3)
0
(0)
  • Rate this reply
View profile
Jul 8, 2011 10:49:21 PM
0
(0)
ACE - Master

This is just a wild thought....because I've never owned a Brother printer nor used a secondary wireless router other than the one in my RG.....but is it possible that you need to re-run your printer installation app. on each PC so it can find the printer in its new location?  When I installed my wireless HP printer and installed the software on each laptop the installation app. automatically located the printer and established connection with it.  Very easy.  This may be of no help to you but I just thought I'd throw it out there.   Perhaps one of our better versed gurus will jump in here with a better suggestion.

The problem with socialism is that you eventually run out of other peoples' money. .......Margaret Thatcher

This is just a wild thought....because I've never owned a Brother printer nor used a secondary wireless router other than the one in my RG.....but is it possible that you need to re-run your printer installation app. on each PC so it can find the printer in its new location?  When I installed my wireless HP printer and installed the software on each laptop the installation app. automatically located the printer and established connection with it.  Very easy.  This may be of no help to you but I just thought I'd throw it out there.   Perhaps one of our better versed gurus will jump in here with a better suggestion.

The problem with socialism is that you eventually run out of other peoples' money. .......Margaret Thatcher
*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: Can't Access Printer From Secondary Router

2 of 4 (1,179 Views)
0
(0)
  • Rate this reply
View profile
Jul 8, 2011 11:39:22 PM
0
(0)
Guru

Thanks, but I just found a long thread about how to properly run a secondary router as an access point behind the RG.  I'll try that tomorrow and see if that solves the problem.  Otherwise, it may not be worth fooling with.  I already removed my CradlePoint router and connected my computers back to the RG via wireless.

Thanks, but I just found a long thread about how to properly run a secondary router as an access point behind the RG.  I'll try that tomorrow and see if that solves the problem.  Otherwise, it may not be worth fooling with.  I already removed my CradlePoint router and connected my computers back to the RG via wireless.

Re: Can't Access Printer From Secondary Router

3 of 4 (1,176 Views)
Highlighted
0
(0)
  • Rate this reply
View profile
Solved
Jul 9, 2011 6:42:25 AM
0
(0)
Guru
Edited by jimgfitzgerald on Jul 9, 2011 at 6:43:12 AM

http://forums.att.com/t5/Residential-Gateway/U-verse-for-BUSINESS-2Wire-3600HGV-bridge-mode-or-anoth...

 

See post #13 by SomeJoe7777.  I followed steps 1 and 2.  IP addresses were OK as was.  I also disabled wireless signal from the U-Verse RG.  Everything seems to be working great.  I have all my wired devices connected to the RG and all my wireless devices connected to my CradlePoint N router.  Thanks Joe for all the good information.

http://forums.att.com/t5/Residential-Gateway/U-verse-for-BUSINESS-2Wire-3600HGV-bridge-mode-or-another-AT-amp/td-p/2707013/page/2

 

See post #13 by SomeJoe7777.  I followed steps 1 and 2.  IP addresses were OK as was.  I also disabled wireless signal from the U-Verse RG.  Everything seems to be working great.  I have all my wired devices connected to the RG and all my wireless devices connected to my CradlePoint N router.  Thanks Joe for all the good information.

Re: Can't Access Printer From Secondary Router

[ Edited ]
4 of 4 (1,172 Views)
Solution
Advanced
You must be signed in to add attachments
Share this post
Share this post