U-verse Forums

Reply
Posted Oct 20, 2012
11:03:46 PM
View profile
2Wire 3600HGV in "Bridge" mode and trying to communicate on Port 68 (bootp)

Hello Everyone,

 

I trying to figure out some connection issues I have been having with some online games.

 

Currently I have AT&T U'Verse Service with a 2Wire 3600HGV modem with Voice Service.

 

I have it currently setup in "Bridge" mode (Not true bridge mode as there is no such thing for this Modem) with a Modified Linksys E3000 Router with dd-wrt flashed to it.

 

During my Firewall Log Monitoring Sessions I noticed that the 2Wire Gateway tries to open a session with my network on Port 68 (bootp typically), and naturally my firewall prevent the connection on this port.

 

Does anyone know why the 2Wire Gateway would be trying to do connect to my internal network on port 68?

 

Any information would be appreciated. 

 

Thanks in advance!

Hello Everyone,

 

I trying to figure out some connection issues I have been having with some online games.

 

Currently I have AT&T U'Verse Service with a 2Wire 3600HGV modem with Voice Service.

 

I have it currently setup in "Bridge" mode (Not true bridge mode as there is no such thing for this Modem) with a Modified Linksys E3000 Router with dd-wrt flashed to it.

 

During my Firewall Log Monitoring Sessions I noticed that the 2Wire Gateway tries to open a session with my network on Port 68 (bootp typically), and naturally my firewall prevent the connection on this port.

 

Does anyone know why the 2Wire Gateway would be trying to do connect to my internal network on port 68?

 

Any information would be appreciated. 

 

Thanks in advance!

0
(0)
  • Rate this reply
View profile
Solved
Oct 21, 2012 7:21:53 AM
0
(0)
Expert
This will be DHCP renewal for your E3000. DHCP responses are on UDP port 68.

You need to allow this in the firewall so that the E3000 can continue to re-verify the public IP address via DHCP with the 2Wire.

The relevant command to properly open the firewall on DD-WRT for DHCP renewal can be found here:

http://www.comprepairgurus.com/att-u-verse2wire-gateway-and-dd-wrt-router-in-dmz-mode/
Accepted Solution

2Wire 3600HGV in "Bridge" mode and trying to communicate on Port 68 (bootp)

3,746 views
2 replies
(0) Me too
(0) Me too
Post reply
Cancel
Submit
Replies
(2)
0
(0)
  • Rate this reply
View profile
Solved
Oct 21, 2012 7:21:53 AM
0
(0)
Expert
This will be DHCP renewal for your E3000. DHCP responses are on UDP port 68.

You need to allow this in the firewall so that the E3000 can continue to re-verify the public IP address via DHCP with the 2Wire.

The relevant command to properly open the firewall on DD-WRT for DHCP renewal can be found here:

http://www.comprepairgurus.com/att-u-verse2wire-gateway-and-dd-wrt-router-in-dmz-mode/
This will be DHCP renewal for your E3000. DHCP responses are on UDP port 68.

You need to allow this in the firewall so that the E3000 can continue to re-verify the public IP address via DHCP with the 2Wire.

The relevant command to properly open the firewall on DD-WRT for DHCP renewal can be found here:

http://www.comprepairgurus.com/att-u-verse2wire-gateway-and-dd-wrt-router-in-dmz-mode/

Re: 2Wire 3600HGV in "Bridge" mode and trying to communicate on Port 68 (bootp)

2 of 3 (3,707 Views)
Solution
0
(0)
  • Rate this reply
View profile
Oct 21, 2012 10:49:56 AM
0
(0)
Contributor

Nice,

 

Worked perfectly, someone really needs to gather up all these little tid bits of info.

 

I probably spent about 3 to 4 hours trying to figure this out alone.

 

Thanks again!

Nice,

 

Worked perfectly, someone really needs to gather up all these little tid bits of info.

 

I probably spent about 3 to 4 hours trying to figure this out alone.

 

Thanks again!

Re: 2Wire 3600HGV in "Bridge" mode and trying to communicate on Port 68 (bootp)

3 of 3 (3,684 Views)
Share this post
Share this post