Ask a question
Search in DIRECTV Forums

DIRECTV Community

Reply
Posted Jan 23, 2013
4:20:00 AM
View profile
RC65 remote problems - New to DTV

I had my Genie system installed a couple of weeks ago and the remotes that came with the system are horrible. They don't respond quickly, seems like the signal is taking a walk to the box. Commands then are buffered and after  5 to 10 seconds the Genie would respond and change the channel 3 or 4 times. Very annoying. I have been reading all the posts on remotes and came to the conclusion that I need an RF capable remote which the RC65 is not.I found the RC65RBX on Amazon for $21.00 and am thinking of getting at least two. My question is except for the TV will it work right out of the box on the Genie and client or do I have to pair the remote with each receiver? Should it come with instructions for setup along with codes for the TV?

Thanks!!

I had my Genie system installed a couple of weeks ago and the remotes that came with the system are horrible. They don't respond quickly, seems like the signal is taking a walk to the box. Commands then are buffered and after  5 to 10 seconds the Genie would respond and change the channel 3 or 4 times. Very annoying. I have been reading all the posts on remotes and came to the conclusion that I need an RF capable remote which the RC65 is not.I found the RC65RBX on Amazon for $21.00 and am thinking of getting at least two. My question is except for the TV will it work right out of the box on the Genie and client or do I have to pair the remote with each receiver? Should it come with instructions for setup along with codes for the TV?

Thanks!!

RC65 remote problems - New to DTV

7,939 views
15 replies
(0) Me too
(0) Me too
Post reply
View all replies
(15)
0
(0)
  • Rate this reply
View profile
Jan 23, 2013 7:55:30 AM
0
(0)
Scholar

I hope U have better luck than I did with receiving an answer.  I asked a question about a week ago and got 1 answer that was of no help in regards to my question.

I hope U have better luck than I did with receiving an answer.  I asked a question about a week ago and got 1 answer that was of no help in regards to my question.

Re: RC65 remote problems - New to DTV

2 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Jan 24, 2013 6:54:33 PM
0
(0)
ACE - Expert

Yes, you have to pair the remote to the receiver.  the remote should come with the instructions but if it does not, the instructions are readily available on the DirecTV.com site

Yes, you have to pair the remote to the receiver.  the remote should come with the instructions but if it does not, the instructions are readily available on the DirecTV.com site

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: RC65 remote problems - New to DTV

3 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Jan 26, 2013 3:02:03 AM
0
(0)
Teacher

Thanks peds. I ordered the new remote the other day hoping it will solve my issues, but I am not sure it will. I think the issue is with the Genie. The reason I say that is due to the fact that I can see the light on the unit flicker so I know it got the command. Last night was extremely frustrating. I would press channel up and nothing would happen, a few seconds later the picture would freeze then a few seconds later it would go black. Then again a fews seconds later it would finally change channels skipping a couple.

Thanks peds. I ordered the new remote the other day hoping it will solve my issues, but I am not sure it will. I think the issue is with the Genie. The reason I say that is due to the fact that I can see the light on the unit flicker so I know it got the command. Last night was extremely frustrating. I would press channel up and nothing would happen, a few seconds later the picture would freeze then a few seconds later it would go black. Then again a fews seconds later it would finally change channels skipping a couple.

Re: RC65 remote problems - New to DTV

4 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Jan 26, 2013 4:15:44 PM
0
(0)
ACE - Expert

Sounds like you might be getting IR interference from your TV.  if this is the case, the RF remote will take care of this.

Sounds like you might be getting IR interference from your TV.  if this is the case, the RF remote will take care of this.

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: RC65 remote problems - New to DTV

5 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Jan 30, 2013 12:22:08 PM
0
(0)
Teacher

I just received my RC65RBX remote and looking at the instructions to pair it with the Genie it states to enter the code for the receiver. Looking at the list of codes I do not see the HR34. Do I use one of the DirecTV codes of 00001 or 00002?

I just received my RC65RBX remote and looking at the instructions to pair it with the Genie it states to enter the code for the receiver. Looking at the list of codes I do not see the HR34. Do I use one of the DirecTV codes of 00001 or 00002?

Re: RC65 remote problems - New to DTV

6 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Jan 30, 2013 2:45:53 PM
0
(0)
ACE - Expert

you need to enter the last 6 digits of the RID (Receiver ID) number.  the RID number can be found inside the access card door.  But if you follow the on screen menu to program the HR34 to RF, it will tell you the number to enter.

you need to enter the last 6 digits of the RID (Receiver ID) number.  the RID number can be found inside the access card door.  But if you follow the on screen menu to program the HR34 to RF, it will tell you the number to enter.

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: RC65 remote problems - New to DTV

7 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Jan 31, 2013 6:32:32 PM
0
(0)
Contributor

No it won't I have the same problem and it didn't work. Why can't Direct TV just admit there is a problem and they have no answer ?  I have Direct TV coming tomorrow, 4th time in a month, same problem, they have no answer.

No it won't I have the same problem and it didn't work. Why can't Direct TV just admit there is a problem and they have no answer ?  I have Direct TV coming tomorrow, 4th time in a month, same problem, they have no answer.

Re: RC65 remote problems - New to DTV

8 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Jan 31, 2013 9:29:31 PM
0
(0)
Tutor

The RC65RBX will not work with the Genie client (C31-Small box) in RF mode, only with the main HR34 receiver. This remote for some reason needs the RID# which only receivers have; hence the name Receiver I D. The Genie clients have no RID because they are not a receiver, therefore the RC65RBX will not work in RF mode with the Genie Client. The non backlit RC65RX will however work fine for the Genie client in RF mode because it doesn't require a RID. I don't know what's so hard to make  the RC65RX backlit that doesn't require a RID. No other remote requires this. 

The RC65RBX will not work with the Genie client (C31-Small box) in RF mode, only with the main HR34 receiver. This remote for some reason needs the RID# which only receivers have; hence the name Receiver I D. The Genie clients have no RID because they are not a receiver, therefore the RC65RBX will not work in RF mode with the Genie Client. The non backlit RC65RX will however work fine for the Genie client in RF mode because it doesn't require a RID. I don't know what's so hard to make  the RC65RX backlit that doesn't require a RID. No other remote requires this. 

Re: RC65 remote problems - New to DTV

9 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Feb 1, 2013 2:43:01 AM
0
(0)
Professor

The only difference in the RC65RX and the RC65RBX is the backlighting, nothing else. If your RC65RBX isn't bringing up the same menu options as the RC65RX, then do the following on the RC65RBX:

 

 

 

1. dtv

2. press and hold MUTE & SELECT, wait for two blinks, release

3. enter 9 6 3

4. press CH UP

The only difference in the RC65RX and the RC65RBX is the backlighting, nothing else. If your RC65RBX isn't bringing up the same menu options as the RC65RX, then do the following on the RC65RBX:

 

 

 

1. dtv

2. press and hold MUTE & SELECT, wait for two blinks, release

3. enter 9 6 3

4. press CH UP

Re: RC65 remote problems - New to DTV

10 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Feb 1, 2013 5:02:37 AM
0
(0)
Teacher

Programmed and working as designed. Still have the lag in changing the channels, must be something with the receiver. It is very frustrating to have to wait 5 to 10 seconds for the channel to change. It is not at the time but enough to make me question my choice of going to DTV.

Programmed and working as designed. Still have the lag in changing the channels, must be something with the receiver. It is very frustrating to have to wait 5 to 10 seconds for the channel to change. It is not at the time but enough to make me question my choice of going to DTV.

Re: RC65 remote problems - New to DTV

11 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Feb 1, 2013 8:23:42 AM
0
(0)
Professor

vito, you try the opposite to sped up remote time:

 

1. dtv

2. press and hold MUTE & SELECT, wait for two blinks, release

3. enter 9 6 3

4. press CH DOWN

vito, you try the opposite to sped up remote time:

 

1. dtv

2. press and hold MUTE & SELECT, wait for two blinks, release

3. enter 9 6 3

4. press CH DOWN

Re: RC65 remote problems - New to DTV

12 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Feb 1, 2013 11:03:59 AM
0
(0)
Tutor
Quote: Originally Posted by tivoburkee 

The only difference in the RC65RX and the RC65RBX is the backlighting, nothing else. If your RC65RBX isn't bringing up the same menu options as the RC65RX, then do the following on the RC65RBX:

 

 

 

1. dtv

2. press and hold MUTE & SELECT, wait for two blinks, release

3. enter 9 6 3

4. press CH UP

 

The RC65RBX requires an additional step to operate in RF mode which is entering the last 6 digits of the RID#.

This is fine for the HR34 but the Genie client C31 is not a receiver and has no RID#  

therefore will not work in RF mode for the clients.

Quote: Originally Posted by tivoburkee 

The only difference in the RC65RX and the RC65RBX is the backlighting, nothing else. If your RC65RBX isn't bringing up the same menu options as the RC65RX, then do the following on the RC65RBX:

 

 

 

1. dtv

2. press and hold MUTE & SELECT, wait for two blinks, release

3. enter 9 6 3

4. press CH UP

 

The RC65RBX requires an additional step to operate in RF mode which is entering the last 6 digits of the RID#.

This is fine for the HR34 but the Genie client C31 is not a receiver and has no RID#  

therefore will not work in RF mode for the clients.

Re: RC65 remote problems - New to DTV

13 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Feb 1, 2013 11:31:13 AM
0
(0)
Teacher

I have it in RF and did enter the last 6 digits of the RID. When setting it up it did instruct me to enter that code and do a CHNL UP. Will performing the steps in your last post would that help with the lag problem or do you think it is the receiver? 

I have it in RF and did enter the last 6 digits of the RID. When setting it up it did instruct me to enter that code and do a CHNL UP. Will performing the steps in your last post would that help with the lag problem or do you think it is the receiver? 

Re: RC65 remote problems - New to DTV

14 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Feb 1, 2013 1:56:16 PM
0
(0)
Tutor
Quote: Originally Posted by vito_a_d 

I have it in RF and did enter the last 6 digits of the RID. When setting it up it did instruct me to enter that code and do a CHNL UP. Will performing the steps in your last post would that help with the lag problem or do you think it is the receiver? 


Have you tried resetting the receiver? I have the RC65RBX backlit remote in RF mode to the HR34 and there is no lag of which you have. Operates the receiver and TV fine. As I stated before, it will not however operate the Genie clients (C31 Small boxes) in RF mode because the remote requires a RID for RF use which the Client does not have.

When going through the steps, at the end, hitting channel up turns on the RF and chanell down turns it off and uses IR instead.  
On another note, I couldn't get the remote to programe with the Samsung TV through the menu so I had to do it manually.

Quote: Originally Posted by vito_a_d 

I have it in RF and did enter the last 6 digits of the RID. When setting it up it did instruct me to enter that code and do a CHNL UP. Will performing the steps in your last post would that help with the lag problem or do you think it is the receiver? 


Have you tried resetting the receiver? I have the RC65RBX backlit remote in RF mode to the HR34 and there is no lag of which you have. Operates the receiver and TV fine. As I stated before, it will not however operate the Genie clients (C31 Small boxes) in RF mode because the remote requires a RID for RF use which the Client does not have.

When going through the steps, at the end, hitting channel up turns on the RF and chanell down turns it off and uses IR instead.  
On another note, I couldn't get the remote to programe with the Samsung TV through the menu so I had to do it manually.

Re: RC65 remote problems - New to DTV

15 of 16 (166 Views)
0
(0)
  • Rate this reply
View profile
Feb 1, 2013 4:55:22 PM
0
(0)
Tutor

FYI. I was able to get the RC65RBX to work in RF mode by resetting the client (holding the power button in 10 seconds) and resetting the remote (mute select 981) as well, clearing the RF in both and resetting both back to IR mode. Then using the menu to program the remote gave me the 6 digit code needed to program to RF mode. Laughing    

FYI. I was able to get the RC65RBX to work in RF mode by resetting the client (holding the power button in 10 seconds) and resetting the remote (mute select 981) as well, clearing the RF in both and resetting both back to IR mode. Then using the menu to program the remote gave me the 6 digit code needed to program to RF mode. Laughing    

Re: RC65 remote problems - New to DTV

16 of 16 (166 Views)
Share this post
Share this post