Ask a question
Search in DIRECTV Forums

DIRECTV Forum

Reply
Posted Sep 3, 2013
4:10:12 PM
View profile
Sl3

Have a sl3 lnb with 1 port. Connect sat finder, one end to lnb other to hr 21 able to find sat. Inset PI and no difference in strength while moving ant in az. Tilt and elevation good. Do I actually need the PI?

Have a sl3 lnb with 1 port. Connect sat finder, one end to lnb other to hr 21 able to find sat. Inset PI and no difference in strength while moving ant in az. Tilt and elevation good. Do I actually need the PI?

Sl3

88 views
6 replies
(0) Me too
(0) Me too
Reply
View all replies
(6)
0
(0)
  • Rate this reply
View profile
Sep 3, 2013 4:20:10 PM
0
(0)
Employee

you can't use that "meter" with a SWM LNB.  use the receiver built in signal meter to align the dish

you can't use that "meter" with a SWM LNB.  use the receiver built in signal meter to align the dish

*I am an AT&T employee and the postings on this site are my own and don’t necessarily represent AT&T’s position, strategies or opinions.

Re: Sl3

2 of 7 (1 View)
0
(0)
  • Rate this reply
View profile
Sep 3, 2013 5:12:12 PM
0
(0)
Teacher

I should go into a little more detail of my problem.  I did original on iphone and 2 hard to type.  I bought the SlimLine 3 LNB for my RV. Got the PI and a 4 way splitter which I do not need.  I did use the sat finder with the PI not installed and was able to zero in on Az for the strongest signal.  I have it on a tripod located below my house dish.  Az matches. As you mentioned I am unable to see any difference when the PI is installed. Removed satfinder and  I connect it to my HR21, signal strength is 0. The HR21 did configure it as a SL3.  code 771 appears. I have the B Band converter OFF, all cables checked good as I put them inline with my house system and all worked.  I have come to the conclusion my LNB might be bad and ordered a new one.  Any further suggestions would be appreciated.

I should go into a little more detail of my problem.  I did original on iphone and 2 hard to type.  I bought the SlimLine 3 LNB for my RV. Got the PI and a 4 way splitter which I do not need.  I did use the sat finder with the PI not installed and was able to zero in on Az for the strongest signal.  I have it on a tripod located below my house dish.  Az matches. As you mentioned I am unable to see any difference when the PI is installed. Removed satfinder and  I connect it to my HR21, signal strength is 0. The HR21 did configure it as a SL3.  code 771 appears. I have the B Band converter OFF, all cables checked good as I put them inline with my house system and all worked.  I have come to the conclusion my LNB might be bad and ordered a new one.  Any further suggestions would be appreciated.

Re: Sl3

3 of 7 (1 View)
0
(0)
  • Rate this reply
View profile
Sep 3, 2013 5:38:33 PM
0
(0)
Employee

It might just be dish alignment

It might just be dish alignment

*I am an AT&T employee and the postings on this site are my own and don’t necessarily represent AT&T’s position, strategies or opinions.

Re: Sl3

4 of 7 (1 View)
0
(0)
  • Rate this reply
View profile
Sep 3, 2013 6:04:02 PM
0
(0)
Teacher

I Agree it could be but since I have it at the same AZ as home antenna I thought might eliminate that.  My home is a sl5, I think it would be the same bearing as the sl3, could be wrong. Are the tilts all the same?

I Agree it could be but since I have it at the same AZ as home antenna I thought might eliminate that.  My home is a sl5, I think it would be the same bearing as the sl3, could be wrong. Are the tilts all the same?

Re: Sl3

5 of 7 (1 View)
0
(0)
  • Rate this reply
View profile
Sep 3, 2013 6:27:06 PM
0
(0)
Employee

There is no way to set the AZ as your home antenna, as there is no markings on the dish.   AZ gets "set" by sweeping the dish left and right until the satellite is found.  the tilt is the same for both LNB types

There is no way to set the AZ as your home antenna, as there is no markings on the dish.   AZ gets "set" by sweeping the dish left and right until the satellite is found.  the tilt is the same for both LNB types

*I am an AT&T employee and the postings on this site are my own and don’t necessarily represent AT&T’s position, strategies or opinions.

Re: Sl3

6 of 7 (1 View)
0
(0)
  • Rate this reply
View profile
Sep 3, 2013 6:34:09 PM
0
(0)
Teacher

THanks will try tomorrow and let you know.

THanks will try tomorrow and let you know.

Re: Sl3

7 of 7 (1 View)
Share this post
Share this post