Ask a question
Search in DIRECTV Forums

DIRECTV Forum

Reply
Posted Jan 5, 2014
1:06:14 PM
View profile
When I open up guide and then change the channel my screen goes black. n

This seems to be happening more frequently . When change the channel it goes to a blank screen . I can open the menu and guide but it doesn't show a picture in the left upper corner for the channel selected . Even if I scroll through channels or channel up/down it stays black . I finally get frustrated and just turn the tv off . Please help

This seems to be happening more frequently . When change the channel it goes to a blank screen . I can open the menu and guide but it doesn't show a picture in the left upper corner for the channel selected . Even if I scroll through channels or channel up/down it stays black . I finally get frustrated and just turn the tv off . Please help

When I open up guide and then change the channel my screen goes black. n

999 views
5 replies
(0) Me too
(0) Me too
Reply
View all replies
(5)
0
(0)
  • Rate this reply
View profile
Jan 5, 2014 1:08:05 PM
0
(0)
ACE - Expert

what model of receiver do you have. look for the model number inside the access card door..

First thing to try is resetting your DVR/Receiver using the red button behind the front panel access card door. See if that helps. ( on side panel on H25 receivers).

what model of receiver do you have. look for the model number inside the access card door..

First thing to try is resetting your DVR/Receiver using the red button behind the front panel access card door. See if that helps. ( on side panel on H25 receivers).

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: When I open up guide and then change the channel my screen goes black. n

2 of 6 (110 Views)
0
(0)
  • Rate this reply
View profile
Jan 18, 2014 7:54:58 AM
0
(0)
Scholar

I have the same problem and it can temporarily be resolved without doing a time-consuming red-button reset.

if I go into the Settings and view Satellite signals, then exit, the tuner begins to work again IMMEDIATELY (the small window shows live TV as soon as I go to the View Satellite Signals page) and all channels are back to normal.  That remedy has worked.   However, the problem will come back at any time (and, yes, I've done the red button reset too).


DirecTV is replacing the HR-24 HD DVR to try to fix.

I have the same problem and it can temporarily be resolved without doing a time-consuming red-button reset.

if I go into the Settings and view Satellite signals, then exit, the tuner begins to work again IMMEDIATELY (the small window shows live TV as soon as I go to the View Satellite Signals page) and all channels are back to normal.  That remedy has worked.   However, the problem will come back at any time (and, yes, I've done the red button reset too).


DirecTV is replacing the HR-24 HD DVR to try to fix.

Re: When I open up guide and then change the channel my screen goes black. n

3 of 6 (110 Views)
0
(0)
  • Rate this reply
View profile
Jan 18, 2014 9:23:41 AM
0
(0)
Tutor

I answered on a similar thread that I am having the exact same issue.

So I believe DirecTV may be having an issue. 

HEre are my specs:

Genie HR34-700 - in the San Fran Bay area.  Device is 1 year old.

What is really irritating is this happens when recording a show - so the recording is just black. (but I have audio)

I answered on a similar thread that I am having the exact same issue.

So I believe DirecTV may be having an issue. 

HEre are my specs:

Genie HR34-700 - in the San Fran Bay area.  Device is 1 year old.

What is really irritating is this happens when recording a show - so the recording is just black. (but I have audio)

Re: When I open up guide and then change the channel my screen goes black. n

4 of 6 (110 Views)
0
(0)
  • Rate this reply
View profile
Jan 18, 2014 9:25:46 AM
0
(0)
ACE - Expert

See my response to your other post.  Most likely your issue is different, lcalamar, because your audio is fine. 

See my response to your other post.  Most likely your issue is different, lcalamar, because your audio is fine. 

*The views and opinions expressed on this forum are purely my own. Any product claim, statistic, quote, or other representation about a product or service should be verified with the manufacturer, provider, or party.

Re: When I open up guide and then change the channel my screen goes black. n

5 of 6 (110 Views)
0
(0)
  • Rate this reply
View profile
Feb 22, 2014 10:21:45 AM
0
(0)
Contributor

I noticed this become progressively worse over time, so I knew it was something to do with my usage patterns.  My DVR had less than 10% free disk space - around 6% when it finally became unusable.

This is what I did to fix it:

I went though the guide - slowly and painfully at first and started DELETING old shows and series that I had watched.

I got it down to about 30% free then I turned off the STB and turned it on again.

Finally, better response! Not great, but at least usable.

Then I went through and deleted everything that I had watched until I had about 90% free - turned off/on again and....

it's back to normal response times!

I also went into my series manager list and removed about 20% of my list of shows that are no longer running, just to free up some CPU cycles, but freeing up disk space was the key for me.

I have seen similar issues on other DVR boxes, but this is the most extreme symptom I have yet to experience.  It also explains why everything works so well when you get a "NEW" box!

Bottom line:  regularly delete shows you don't want to keep so that your free space doesn't fall below 30%-40% if possible.

This is CLEARLY a poorly tested STB app if a full disk can cause this issue.  I hope this helps someone!

I noticed this become progressively worse over time, so I knew it was something to do with my usage patterns.  My DVR had less than 10% free disk space - around 6% when it finally became unusable.

This is what I did to fix it:

I went though the guide - slowly and painfully at first and started DELETING old shows and series that I had watched.

I got it down to about 30% free then I turned off the STB and turned it on again.

Finally, better response! Not great, but at least usable.

Then I went through and deleted everything that I had watched until I had about 90% free - turned off/on again and....

it's back to normal response times!

I also went into my series manager list and removed about 20% of my list of shows that are no longer running, just to free up some CPU cycles, but freeing up disk space was the key for me.

I have seen similar issues on other DVR boxes, but this is the most extreme symptom I have yet to experience.  It also explains why everything works so well when you get a "NEW" box!

Bottom line:  regularly delete shows you don't want to keep so that your free space doesn't fall below 30%-40% if possible.

This is CLEARLY a poorly tested STB app if a full disk can cause this issue.  I hope this helps someone!

Re: When I open up guide and then change the channel my screen goes black. n

6 of 6 (110 Views)
Advanced
You must be signed in to add attachments
Share this post
Share this post