10-17-2013 6:10 PM
I'm wondering what is the best way to setup my 3801HGV ATT router along with my Amped Wireless RG10000 router and Amped Wireless S10000 repeater. I previously had cable Internet with the Amped Wireless router and repeater. I want to keep them because of the good range that they get. Right now I have the Amped router plugged into the 3801HGV. I configured the 3801hgv so it recognizes the amped router. I can now wirelessly connect to all three.
Is this the best way to configure these routers?
Should my wired connections be from the 3801HGV or the Amped router?
Solved! Go to Solution.
10-18-2013 3:41 PM
It sounds like you have everything setup perfectly. With the wireless, you want to use as few wireless networks as possible that can cover the area that you need, because otherwise, they conflict with each other. So you want the 3801HGV to connect to the Amped Wireless RG10000 and use the Amped Wireless S10000 repeated to extend the wireless of the Amped Wireless RG10000. So the best thing to do is disable the wireless off the 3801HGV. You may not have to, because the 3801HGV operates at the 2.4GHz frequency but the Amped may operate at 5GHz so there may be no issue.
With the wired connections, the best way to do it is to have any U-verse equipment, such as the TV receivers, connected directly to the 3801HGV and all other internet equipment connected to the Amped router.
Hope this helps.
11-06-2013 12:41 PM
I have a simimalr situation and am upgrading fromthe DSL 2wire to this 2 wire I use my apple timecapsule as the router and had to trun off the router feature in the old 2 wire willl I have to do that again? if so how do I do it it was a long process of calls and waiting via att to do it and they charged me for the call( very unfair) but I will likely need to do the same with this new 2 wire right??
11-08-2013 2:10 PM
You are possibly correct. Depending on how you are using your apple time capsule, you will probably need to put your new 2wire in a bridge mode so the routing is handled by your apple time capsule.
If it is just for basic internet browsing on the computer, it should still work without having to do this.
If you have additional settings on your apple time capsule to control your routing for various tasks, then it is probably needed.
To do so:
Hope this helps.
11-24-2013 11:57 PM
You cannot turnn off the DHCP on the 2wire router. Use your AirPort Utility to disable set it up in bridged mode. Leaving our router to handle DHCP.
12-01-2013 8:53 AM
I have a new ASUS rt-66U 802.11AC router that I'd like to use, but the 3801 manual shows configuration screens that I do not ssee when I select the Link Configuration tab. How do I configure the 3801 to use this router? The manual speaks of putting the 3801 in the bridge mode but I don't see how to do it.
12-01-2013 11:44 AM
See the following post for instructions to set up your own router using the DMZPlus feature:
03-18-2014 8:45 AM
Welcome to the internet boards! Check out our troubleshooting articles below and don’t forget to search the forums - your question may have been answered already!
Service acting up? Click here to troubleshoot now!
For DSL related issues. We highly recommend chatting with our teams to address this as quickly as possible.
© 2017 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!