07-04-2012 6:48 PM
I am posting this so hopefully this will save others from the pain of trying to figure this out...I have older Airport Express G, but this should also work for the newer N ones. Problem was that each time I tried to configure the AE it would die at the end step "setting up configuration" and I would lose access and had to keep doing resets. Here is how I solved this. Have on hand ethernet cable, paper clip for resetting.
I'm on 10.7 but I prefer the older airport utility 5.6. and with the older AE's I had to use it. You can download it here:
1. Do a factory reset of your AE by inserting paperclip into little reset button, plugging in the AE and then keep the button pressed until you see rapid flashing. (perhaps not required but I like to start clean).
2. Go into your router control panel for my router that's 192.168.1.254. But you can find your IP on a sticker on your actual modem.
3. Set the Wireless password type on your modem/router to WPA2-PSK (AES).
4. save configuration
5. I like to connect to my AE via ethernet for setup, if you do too, then plug your AE to your machine via an ethernet cable. 6. Launch Airport Utility 5.6
7. Select the AE and setup as usual.
the key to the solution is that your AT&T router/modem wireless password is WPA2-PSK (AES).
(note this is for simply extending your network or using your AE to play music, not for using the AE as an independent router).
Solved! Go to Solution.
07-06-2012 1:53 PM
Thanks for posting the information. This information may be helpful to Uverse customers. The posts discussing how to configure PPoE, not so much. (Uverse internet doesn't use PPoE).
07-06-2012 8:37 PM
Cool. Good to know. I'll see if I can move the other post.
Just so other readers know the commentor is referring to a different post not this one. Setting up Airport Express to simply listen to music/AirPlay doesn't have to do with PPPoe so these instructions should work for either u-verse or dsl folks.
12-18-2012 3:17 PM
OK, I have tried to do this for abut 3 hours now. No luck. I will try what your post says.Appreciae you taking the time to hlep folks like me. Question for you. You said to set the password type to WPA2-PSK (AES).. Mine is currently set to WPA-PSK (TKIP)/WPA2-PSK (AES). Doesn't that cover all bases? Also, what do you set the AE setting to? Nothing matches exactly with the Pace settings.
I did get the AE connected to my network but never could get it to work in iTunes (except one time, briefly), but it is listed in the itunes menu. Then suddenly the AE would connect to nothing? Very frustrated.
12-18-2012 6:09 PM
You must use the WPA2-PSK (AES) setting not the WPA-PSK (TKIP)/WPA2-PSK (AES). This is what tripped me up when I initally tried setting things up. So this is an important step.
This might be why it's dropping the connection. Make sure both your router/modem AND the Airport Express are BOTH set to WPA2-PSK (AES) for the password security, then make sure you have the correct password entered into your Airport Express. (I usually like to do a factory reset to make sure I'm not working with any old, bad settings when troubleshooting).
Use airport utilitiy 5.6, it has a lot better control over the settings than the new version of the airport utility.
07-21-2013 6:08 PM
I do not know you....but i love you. Thank You...7 hours wasted on this same problem! Thank you Thank you thank you!
Welcome to the internet boards! Check out our troubleshooting articles below and don’t forget to search the forums - your question may have been answered already!
Service acting up? Click here to troubleshoot now!
© 2017 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!