- edited 10-10-2014 10:27 AM by ATTU-verseCare
i just can't figure out how to connect internet to my smart t.v. i have entered everything that the t.v. tells me to do and all i get is 'can't find internet'. please help and make it simple. i'm not that tech. smart. thanks for any help.
Solved by: Go to Solution.
03-09-2014 3:24 PM
my t.v. is a phillips 3000 serials led-lcd 46 inch smat t.v. #46PFL 3608/F7. i have tried all different ways of tryin to connect but it just won't. thanks for any help i can get.
- edited 03-10-2014 12:03 AM
You have two options you can try, WPS and Passcode. If one succeeds, you don't have to do the other.
FOR WPS Set-up
You'll have to enable WPS on your RG.
Continue by configuring your TV's Wireless connection.
There are some secuirty concerns with leaving WPS tuned on. It's recommended you turn it off after you have paired your TV by following steps 1-4 under enabling WPS, except choosing Off on step 4.
FOR NETWORK KEY SET-UP
You will need to know your SSID and your Network key. You can find these printed on the side of your RG or on the Residential Gateway Portal.
03-12-2014 6:40 PM
08-31-2016 5:22 AM
good morning, i'm also having the same exact problem with setting up my wireless internet to the phillip's smart tv. i have gotten to the easy setup then after it goes through it say that it can't connect that home is not active.. don't know what to do. please help me:
08-31-2016 5:27 AM
where do i find my passcode??? with setting up wireless internet to phillips smart tv
12-01-2017 12:40 PM
I followed all the instructions for setting up my tv using the ssid type connection, however after it stopped scanning it stated that connection failed. When I tried to use the 'scan' method the tv displayed 'no connection (wifi) found' I made numerous attempts. What might I be doing incorrectly?
01-01-2018 8:13 AM
My Phillips smart tv will not connect to my AT&T hotspot but all my other devices do? Can you help
02-02-2018 5:40 PM
I have a Samsung smart tv. When I try to get on the internet I get an error message. Looking for a solution it said I am connected to my local network but unable to connect to the internet. It tells me to check the DNS settings on my IP Settings. It shows the DNS Server as 0.0.0.0. from what I found on Youtube it tells me to manually change the DNS to 188.8.131.52. I have tried that with no success. What should I do?
02-08-2018 10:21 AM
Att told me I would have everything to use my wifi to my tv. It's saying router not detected
02-08-2018 10:30 AM
@myra.ackland AT&T wifi for your smart TV DOES work. I've had mine (Sharp) using my AT&T internet for a few years now.
The trick is to either let the TV find your 'network' and then enter the password off your router. If, for whatever reason, your TV is not finding your router/network, you may have to give a it a nudge.
What brand and model is the TV?
02-10-2018 11:56 AM
thank you but i have no clue as to what you are describing. On my tv it ask for password which i put in but it said try again. I did but its not working.
just clicked on WPS on internet box and it is blinking. Don't know what that is either. Gjuess I should just call ATT
12-14-2018 9:31 PM
How do i get Phillips Smart TV model 55PFL5402/F7 to receive Wi-Fi signal from my ATT Uverse
05-24-2019 8:32 PM
i can't connect my smart tv to the internet. It says i'm connected to the server but not the internet and to contact my internet service provider
Visit these related resourcesView New Device Help!