03-16-2011 8:18 AM - edited 03-16-2011 8:59 AM
I am having trouble properly configuring this AT&T 2Wire 3600HGV modem for my network. Maybe someone is aware of a different firmware for this product?
I am completely aware of how to setup the DMZ mode & router behind router setup in these boxes but that is NOT the point. (We have supported firewalled networked equipment working that has all the bells & whistles including QoS)
In the event of a factory reset of the AT&T 2Wire VDSL modem at this business, I want to properly insure the following business requirements are met:
- DHCP - OFF (at min, it appears you must leave one available?)
- WiFi - OFF (Yes this can be turned off, but bridging it always insured it was turned off in the past. ON is a security concern among just bad business i.e. conflict with other business WiFi, employees might see/use this non-content filtered WiFi, etc etc)
- & passing off internet service needs to be easy to another networked supported OUTSIDE of AT&T firewall. (I'm NOT asking for AT&T support on this, but in the bridge DSL world, this was EASY)
- if bridging this 2Wire is NOT an option, backing up the configuration settings would be a nice alternative but that is not available as well?
Bridging the old DSL modems always worked nicely but the 2Wire 3XXXHGV line appears to be the ONLY ones to support the AT&T VDSL Max Turbo speeds. 24Mbps down / 3 Mbps up which we use not only for normal business operations (credit cards, business email, web based training, etc) but this high speed is required to view onsite security video (3Mbps up) and offer customers FAST free WiFi!
AT&T U-Verse offers the right price, contract, speed, internet package & installers to properly handle our resturant locations company's data needs but I'm struggling with the their "business" support of this 2Wire VDSL modem product. We ONLY use the internet, no TV (not legally available for restaurants, yet). No Voip because POTS is our reliable backup. So it's just the internet service ...
For coverage on AT&T Uverse, we have over 50 locations lit up like a Christmas tree but sadly business support on this product is driving me nutz! Maybe because I now see this is listed under "Residential Gateway"? Is this AT&T 2Wire VDSL modem product not meant for business? Is anyone aware of another supported AT&T VDSL modem or a different 2Wire firmware available? Official AT&T support has me running in circles (AT&T U-verse support > AT&T Connecttech > AT&T Connecttech360 > AT&T U-verse support, rinse, repeat)
Solved! Go to Solution.
09-01-2013 8:06 AM
After my spam of replies I have fixed my problem. I had to set the router to static and type in the gateway, dns servers, etc that is listed on the uverse box. Port forwarding works fine now on the linksys. Yay!
09-01-2013 6:10 PM
09-23-2013 8:27 PM
i recently moved from the country where the only available static IP was a very expensive T1 line. Now in the city I had two choices, AT&T or Time Warner. After much discussion with AT&T representatives that uVerse would provide me with the same capability to manage my block of 32 static IP addresses, I pulled the plug and moved my equipment to the new location, expecting at one or two day outage. That was a week ago. WIth the end on the month approaching and no access to my accounting system (LegerSMB), I am running out of time. i have poured through the forums looking for a solution, but it has eluded me. Here is my setup.
I run my own, DNS (named), DHCP, sendmail MTA, bacula, ejabberd, Mailman servers, CalDav, and apache servers from behind my fire wall. Some of the servers are physical, some are KVM hosted, some are apache virtual web hosts. The only connection to the 3801 is my linux based (centos) firewall that manages the connection to the internet. It has all of the active static IP addresses set up as eth0, eth0:1, eth0:2, etc. The 3801 recognizes the eth0 static IP address 220.127.116.11, passing traffic both directions. 18.104.22.168:80 is correctly NAT'ed to the apache server behing the fire wall, for example. Everything from inside the firewall is working correctly with data passng to and from the internet. We can send mail internally or externally and can receive mail, from inside the firwall, for example. I am willing to change the configuration anywhere in my system, provided it does not change the presentation to the end users either on the local net or the internet.
Here is the question. Can this be made to work and how, or should I move to Time Warner Cable? I am concerned that I'd be moving from the frying pan to the fire. I asusmed an internet company would be better prepaerd than a cable company. :-)
Any Help, much appreciated.
09-24-2013 6:23 AM
09-24-2013 9:53 AM
Sorry, too much superfluous information, I suspect. My problem is, except for 22.214.171.124, the internet cannot see any of my static ip addresses, including my dns servers on 126.96.36.199 and 125. So no DNS lookup is occurring. Even if that worked and pointed to my web server on 98, for example, the 3801 does not pass the 98 traffic to my firewall. So you can go to the web server on 97 (but not by name) but cannot get to any of the other servers or services on 98 through 125 by ip or name.
I am hoping there is a change I can make in my firewall as a workaround or a change to the 3801.
09-24-2013 2:25 PM - edited 09-24-2013 2:29 PM
What you're running into is a limitation of the 2Wire gateway in that it is hard coded to expect a 1-to-1 relationship between IP addresses and MAC addresses. Each static IP address you're using must appear to the 2Wire gateway to be coming from a different MAC address. I suspect that your Linux router is answering the 2Wire with the same MAC address for all IP addresses, which will not work.
If your Linux router can assign different MAC addresses to eth0:1, eth0:2, etc. then that should solve the problem.
If not, there is another potential workaround if your 2Wire gateway is running the very latest firmware (188.8.131.52). Can you log into the 2Wire and check to see what firmware version it's running?
09-24-2013 2:40 PM
The FW level is 184.108.40.206-enh.tm. The eth1:X is more like an iP alias. All of the :X's share the eth1 mac address. More over putting MACADDR= or HWADDR in the X's is ignored and the eth1 mac address is inserted.
09-24-2013 3:36 PM - edited 09-24-2013 3:37 PM
OK, I have not tested this because it is so new. But you are a good candidate for the cascaded router option in the new firmware. Follow these steps:
Those servers should now be able to reach the internet, and you can configure the firewall on the Linux router as you want. Some other notes:
09-24-2013 3:51 PM
Thanks, SomeJoe7777. I too am on a business trip. Since this requres taking the interface down with the potential of it not coming back up, I'll try it when I get home. After you described the problem for me, I was able to find a potential way to get my firewall to present a different mac address for each ip by using the bridge function and taps. If I get that to work, I'll post the solution.
10-05-2013 10:06 PM
I'm not sure if this is still an active post, but i'm trying to figure out a couple things in your config or really just wanted to double check.. what does the address 192.168.160.20 belong to? My first thought was an attach switch from your router connect to int fa0/0 on the switch.
I'm trying to figure out how to get my 2600 cisco router to play nice with my AT&T router. I have followed the instructions that you have provided, well the best that i can anyways..
my setup is like this:
Port 2 on the AT&T router is connect to the Cisco 2600 router on port fa0/1
Cisco 2600 port fa0/0 is connect to 2950 layer 2 switch on port 23
Host machine is connected to port 1 on the 2950 switch
this setup allows me to ping the outside world like google, yahoo etc from the my host machine but does not allow me to use an internet browser to browse to the site. it just keeps loading with no results. I believe this has something todo with my acl or routing. I was wondering if you or anyone could please take a look at my configs and suggest anything that might help..
is setup as a bridge per your instructions (DMZplus mode)
Current configuration : 1047 bytes
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
enable password password
no aaa new-model
ip name-server 220.127.116.11
ip name-server 18.104.22.168
ip dhcp pool TEST_CLIENTS
network 192.168.2.0 255.255.255.0
dns-server 22.214.171.124 126.96.36.199
description Internal LAN
ip address 192.168.2.254 255.255.255.0
no ip redirects
no ip proxy-arp
ip nat inside
arp timeout 600
ip address dhcp (this recieves the public IP address)
no ip redirects
no ip proxy-arp
ip nat outside
no cdp enable
ip nat inside source list 101 interface FastEthernet0/1 overload
no ip http server
access-list 101 permit ip 192.168.2.0 0.0.0.255 any
line con 0
line aux 0
line vty 0 4
SWITCH 2950 CONFIGS
ip name-server 188.8.131.52
ip name-server 184.108.40.206
ip ssh time-out 120
ip ssh authentication-retries 3
spanning-tree mode pvst
no spanning-tree optimize bpdu transmission
spanning-tree extend system-id
ip address 192.168.2.2 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.254
ip http server
10-06-2013 8:57 AM
10-07-2013 6:48 PM
Thanks you for the responce, below is the information that you requested.
Gateway of last resort is 220.127.116.11 to network 0.0.0.0
18.104.22.168/22 is subnetted, 1 subnets
C 22.214.171.124 is directly connected, FastEthernet0/1
192.168.1.0/32 is subnetted, 1 subnets
S 192.168.1.254 [254/0] via 126.96.36.199, FastEthernet0/1
C 192.168.2.0/24 is directly connected, FastEthernet0/0
S* 0.0.0.0/0 [254/0] via 188.8.131.52
FastEthernet0/1 is up, line protocol is up
Internet address is 99.109.100.xxx/22 (my public IP address I X'ed the last octet hope thats ok, but it is my public IP address)
Broadcast address is 255.255.255.255
Address determined by DHCP
MTU is 1500 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is disabled
Local Proxy ARP is disabled
Security level is default
Split horizon is enabled
ICMP redirects are never sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
IP CEF switching is enabled
IP CEF Feature Fast switching turbo vector
IP multicast fast switching is enabled
IP multicast distributed fast switching is disabled
IP route-cache flags are Fast, CEF
Router Discovery is disabled
IP output packet accounting is disabled
IP access violation accounting is disabled
TCP/IP header compression is disabled
RTP/IP header compression is disabled
Policy routing is disabled
Network address translation is enabled, interface in domain outside
WCCP Redirect outbound is disabled
WCCP Redirect inbound is disabled
WCCP Redirect exclude is disabled
BGP Policy Mapping is disabled
And sorry about the late responce
10-08-2013 5:44 PM
10-09-2013 1:44 AM
After 3 weeks of effort, with support from 3 levels of AT&T tech support as well as this forum, I have concluded that the AT&T router is incapable of supporting my environment. I installed Time Warner Cable Business Internet last Friday and had my environment running in less than 3 hours. (The only reason it took 3 hours, was that TWC had messed up a routing table which caused the routing to go into an infinite loop resulting in a timeout. Bottom lline, the TWC router worked just like the T1 router, passing everything down the pipe.
I want to thank SomeJoe for his effort in trying to get this to work. Another week of work may have yielded sucess, but I ran out of time.
Welcome to the internet boards! Check out our troubleshooting articles below and don’t forget to search the forums - your question may have been answered already!
Service acting up? Click here to troubleshoot now!
For DSL related issues. We highly recommend chatting with our teams to address this as quickly as possible.
© 2017 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!