03-16-2011 8:18 AM - edited 03-16-2011 8:59 AM
I am having trouble properly configuring this AT&T 2Wire 3600HGV modem for my network. Maybe someone is aware of a different firmware for this product?
I am completely aware of how to setup the DMZ mode & router behind router setup in these boxes but that is NOT the point. (We have supported firewalled networked equipment working that has all the bells & whistles including QoS)
In the event of a factory reset of the AT&T 2Wire VDSL modem at this business, I want to properly insure the following business requirements are met:
- DHCP - OFF (at min, it appears you must leave one available?)
- WiFi - OFF (Yes this can be turned off, but bridging it always insured it was turned off in the past. ON is a security concern among just bad business i.e. conflict with other business WiFi, employees might see/use this non-content filtered WiFi, etc etc)
- & passing off internet service needs to be easy to another networked supported OUTSIDE of AT&T firewall. (I'm NOT asking for AT&T support on this, but in the bridge DSL world, this was EASY)
- if bridging this 2Wire is NOT an option, backing up the configuration settings would be a nice alternative but that is not available as well?
Bridging the old DSL modems always worked nicely but the 2Wire 3XXXHGV line appears to be the ONLY ones to support the AT&T VDSL Max Turbo speeds. 24Mbps down / 3 Mbps up which we use not only for normal business operations (credit cards, business email, web based training, etc) but this high speed is required to view onsite security video (3Mbps up) and offer customers FAST free WiFi!
AT&T U-Verse offers the right price, contract, speed, internet package & installers to properly handle our resturant locations company's data needs but I'm struggling with the their "business" support of this 2Wire VDSL modem product. We ONLY use the internet, no TV (not legally available for restaurants, yet). No Voip because POTS is our reliable backup. So it's just the internet service ...
For coverage on AT&T Uverse, we have over 50 locations lit up like a Christmas tree but sadly business support on this product is driving me nutz! Maybe because I now see this is listed under "Residential Gateway"? Is this AT&T 2Wire VDSL modem product not meant for business? Is anyone aware of another supported AT&T VDSL modem or a different 2Wire firmware available? Official AT&T support has me running in circles (AT&T U-verse support > AT&T Connecttech > AT&T Connecttech360 > AT&T U-verse support, rinse, repeat)
Solved! Go to Solution.
05-31-2013 2:31 PM
06-01-2013 10:24 PM - edited 06-01-2013 10:33 PM
Joe, thanks for the great instructions. I purchased a new wireless router (TP-LINK TL-WDR3500 Wireless N600 Dual Band) to get better signal and speed in my house with 5 PCs on LAN and a few devices on wifi. It does actually work very well even in areas of my house that the 2Wire barely reached. Initially I followed your post 13 only using the wireless features of the TP-Link. I had one issue with wireless dropping out once in a while on the 2.4GHz while the 5GHz kept working nonestop. Couldn't figure out the problem and went as far as resetting both the 2Wire router and the TP-Link. It wasn't too bad and every other day or so I had to reboot the TP-Link to get the 2.4GHz working again.
I then decided to follow your instructions from post 2. I got everything working after I gave the TP-Link a static IP. No more issues with wireless dropping (knock on wood). It's nice to have everything under one router and bypassing the 2Wire. I have one issue remaining and I am hoping you may have an answer. I have a Server 2012 Essentials running for backups and media streaming. The client PCs have been deployed with skipping domain setup (trick found at Paul Thurrot's site). Almost everything works between clients and server (backup, media, shared folders, dashboard), except "Anywhere Access" (remote web access) which allows the connection to the server and its clients from "anywhere" via a domain name.
The server is directly hooked up to the TP-Link and uses the same IP range as everything else. Remote Access worked fine when everything was running through the 2Wire alone. When I try to set this up with the TP-Link behind the 2Wire I get an error that the server is blocked. The wizard set port forwarding on the TP-Link router correctly (443 and 80) for this to work and I see the entries. The wizard is smart enough to suggest that there is more than one router on the LAN and that they may not be working together properly.
It seems that even though the correct ports are forwarded somehow the 2Wire prevents this from working. The server wizard lists the correct server IP address and the TP-Link as default gateway.
enough rambling. any hints are appreciated.
06-02-2013 8:50 AM
06-02-2013 10:09 AM
thanks Joe, it worked fine with just the 2Wire router and I do not have wireless STBs. I will go back and carefully look at the TP-Link settings. In the meantime I found in the MS 2012 forums that it is a common problem that the remote access stops working in a multi router situation. I still have to digest what their conclusions are. There are some directions but I do not understand them entirely.
thanks for your help.
06-02-2013 11:06 PM
Well, wouldn't you know. I did some browsing, after I wrote my post, around the wireless router settings and there were settings for IPTV http://imageshack.us/a/img600/8780/router1.png
I set the correct port and it worked. I didn't get any freezes. nothing. I was finally able to get rid of the hub I was using to splice the feed from the RG.
There's also settings for the unicast and multicast items you mentioned in my router as well. http://img266.imageshack.us/img266/7947/router2s.p
I'm assuming I don't have to tweak those since I'm getting the TV feed just fine.
Now, my only problem is my wireless router isn't sending out the wifi signal but I don't know if that's a result of me switching on that IPTV setting. I'm guessing it isn't but I'm going to bug ASUS about that tomorrow. Would you have any suggestions on that?
and Thanks again
06-03-2013 7:42 AM
06-03-2013 10:14 PM
so I fiddled around a little more with the TP-Link router and the Server 2012 Essentials issue of non-working remote access. After giving up I removed all special settings I applied (e.g. forwarding not under UPnP) or giving the server a static IP or putting into DMZ mode from the TP-Link).
A day later it started to work. I have no idea why. I have a slight guess that it may have to do with certificate reinstated for the server which may have taken some time after I initialized the Anywhere Access with the new router.
All works - thank you Joe!
06-16-2013 8:56 PM - edited 06-16-2013 9:05 PM
I have read through this entire thread (across several of days of course...tons of good info here!) and have 2 external wireless AP's running on my network (both hard-wired back to the RG), as according to post #13, along with wireless enabled on the 2-wire 3801HGV itself. I can connect to any one AP just fine, but switching from one to the other when walking throughout the house causes issues. My devices can see each AP's signal but cannot get an IP address when switching to a different AP. I suspect this is due to caching on the RG itself (it is handling the DHCP), as when I "Clear the List" on the LAN->Status page of the RG, I can then connect to a different AP just fine. This happens no matter which AP I switch to or from - I have to "Clear the List" each time to get a connection. When using only one AP (doesn't matter which one but the other two disabled), everything works fine when connecting/disconnecting. I am using the same SSID on all 3 AP's, but have tried having 3 different SSID's with the same result. Am I right there is a caching or DHCP release/renew issue on the 2-wire RG itself and is there a fix?
At one point I threw in the towel on having the 2-wire do the DHCP and set up a 2nd router using the "post #2" instructions. Everything worked in my test, but that isn't a long-term solution for me due to needing the 2-wire for my TV STB's. The way my house wiring is set up, I don't have the ability to run 2 separate networks for each, hence why I am doing AP's only.
This has been so frustrating...please help!
06-17-2013 12:28 PM
06-17-2013 1:43 PM
06-17-2013 4:04 PM - edited 06-17-2013 4:05 PM
Well, there are a few other people who have reported that they're using the 2Wire + another wireless access point together and are able to roam between them. However, I don't think anyone has reported that they're doing it with 2Wire + 2 additional WAPs.
Indeed, it could be the 2Wire's DHCP causing problems. You may try to factory reset the 2Wire, I've seen that cure some inexplicable problems in the past.
06-19-2013 7:52 AM
06-19-2013 4:06 PM
06-21-2013 10:27 AM
One other interesting tidbit - when both AP's are connected through the 2-wire, using the Wifi Analyzer app on my tablet, I see that one of the AP's signals cuts in and out while the other stays constant. It's visible for a couple seconds, and then cuts out for a couple seconds (and back and forth like that continously). However, when both AP's are running through the Linksys router, both signals are constant and do not disappear. How would the 2-wire be affecting the signal/connection like this?
06-21-2013 11:02 AM
Welcome to the internet boards! Check out our troubleshooting articles below and don’t forget to search the forums - your question may have been answered already!
Service acting up? Click here to troubleshoot now!
© 2016 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!