01-05-2013 8:26 PM
Hello, does anyone know how to help with this?
I have the 3801HGV AT&T Router, and I'm trying to connect two XBOXes. Each XBOX is a Cat-5 Lan Connection that goes directly into the back of the Router. When I connect them to Xbox Live, one of them has no issues, and the other one will set the NAT to Moderate. This prevents me and my son from forming a party to chat while we play games. Sometimes, if I restart the connection test several times on both xboxes, they will both have a NAT Open - but it isn't consistent.
I have tried putting both Xboxes behind a Netgear N600 Router, but this had the exact same results. Initially I tried connecting through the N600's WAN but that wouldn't work at all. But then I connected the router directly to a LAN port on the N600, and connected the two xboxes to the N600's other LAN ports. Basically I think I set up the N600 as a switch. I did this by disabling the N600's DHCP, enabling UPNP, and choosing "automatically assign IP." Note that I did initially try to set the N600 to a static IP address (i used 192.168.1.253), but this method did not work either, as when I logged onto the AT&T router, I could not find it.
So basically - my biggest issue is that I can't get the AT&T router (192.168.1.254) to recognize my Netgear N600 router. It sees it as a switch, but I can't "see it" in the AT&T router's user interface. If I could, then I could put the N600 on the DMZ and it would be fine. But...I can't no matter which way.
PS an AT&T rep came tonight and tried to resolve the issue by putting in a Netgear Gs108 switch, but the same results occur.
Any thoughts? I'd like to smack Microsoft for only allowing one port for the xbox.
Does this make sense?
Solved! Go to Solution.
01-07-2013 10:58 AM - edited 01-07-2013 11:03 AM
Go into the RG's GUi, Settings -> System Info -> enable Router-Behind-Router Detection. Change your router's settings back to a L3(routing) device not L2(switching).
Reboot your RG. Set the router to DMZ mode and assign it a static IP. Reboot the devices and possibly the RG.
Option #2: Open up the Xbox live ports on xbox1 and assign DMZ mode to xbox2.
01-07-2013 10:00 PM
01-08-2013 5:17 AM - edited 01-08-2013 5:30 AM
You don't need to disable DHCP since your router will be using DHCP to assign IP addresses to your Xboxs. The networks need to be different meaning the link from Router -> Modem should be on 192.168.1.x network and the Router -> Xbox should be on a different network (like 192.168.2.x).
You don't need to setup a specific IP for the router in your modem.
Here's a step by step on option 2: http://forums.att.com/t5/Residential-Gateway/U-ver
Once you put your router into DMZ mode, it is in charge of NAT and port forwarding.
After completing these steps, try to see the IP addresses of the xboxs (here). If they are assigned an IP address of 192.168.1.x, then either the RG isnt detecting your router as a piece of routing equipment or your router uses 192.168.1.x network which needs to be changed.
For option 1 did you open up all these ports for one of your xboxs while leaving the other in DMZ?
01-08-2013 1:24 PM
01-09-2013 10:06 AM - edited 01-09-2013 10:07 AM
Good question. You can choose which devices are on which piece of routing equipment. Here's an example:
Router WAN port: 192.168.1.4
Router Gateway IP: 192.168.2.1
01-09-2013 11:29 AM
12-21-2013 3:14 PM
I have the same problem. Option #2 didnt work so I need to look at option #1. In option #1 did he use the N600 or was all this done on the 3801 HGV?
Welcome to the internet boards! Check out our troubleshooting articles below and don’t forget to search the forums - your question may have been answered already!
Service acting up? Click here to troubleshoot now!
© 2017 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!