Ask a question
Search in Internet Forums

Internet Forum

Reply
Posted Aug 8, 2013
5:08:26 PM
View profile
Need help connecting Chromecast to uverse router

I tried connecting chromecast to my 2wire router and having issues. Google is saying that UPnP needs to be enabled but I can't see anything in router settings to do this. Any ideas?

I tried connecting chromecast to my 2wire router and having issues. Google is saying that UPnP needs to be enabled but I can't see anything in router settings to do this. Any ideas?

Accepted Solution

Need help connecting Chromecast to uverse router

46,826 views
13 replies
(6) Me too
(6) Me too
Reply
View all replies
(13)
0
(0)
  • Rate this reply
View profile
Aug 10, 2013 1:35:37 PM
0
(0)
Contributor

I'm having the same issue, with the 3801HGV 2WIRE router.  I found a user guide for it, but I can't find any mention of toggling uPnP. I found the guide here by the way.  Are there so few U-verse subscribers having this issue with Chromecast?  This should have been addressed by now.  Any help with this, AT&T?

I'm having the same issue, with the 3801HGV 2WIRE router.  I found a user guide for it, but I can't find any mention of toggling uPnP. I found the guide here by the way.  Are there so few U-verse subscribers having this issue with Chromecast?  This should have been addressed by now.  Any help with this, AT&T?

Re: Need help connecting Chromecast to uverse router

2 of 14 (46,645 Views)
0
(0)
  • Rate this reply
View profile
Aug 10, 2013 3:42:13 PM
0
(0)
Tutor

Beyond my pay grade.  Need to get into router and disable the "AP Isolation," whatever that is, I think.  

 

I agree - AT&T should have a fix for this by now.

Beyond my pay grade.  Need to get into router and disable the "AP Isolation," whatever that is, I think.  

 

I agree - AT&T should have a fix for this by now.

Re: Need help connecting Chromecast to uverse router

3 of 14 (46,629 Views)
0
(0)
  • Rate this reply
View profile
Solved
Aug 10, 2013 5:07:24 PM
0
(0)
Tutor

NEVER MIND!  I had pulled the HDMI from the (new) AT&T DVR and replaced it with the Chromecast HDMI.  Once I added the Chromecast to another empty slot it worked.  

NEVER MIND!  I had pulled the HDMI from the (new) AT&T DVR and replaced it with the Chromecast HDMI.  Once I added the Chromecast to another empty slot it worked.  

Re: Need help connecting Chromecast to uverse router

4 of 14 (46,612 Views)
Solution
0
(0)
  • Rate this reply
View profile
Nov 9, 2013 2:06:02 PM
0
(0)
Voyager

I'm having this same problem, but I don't understand the described solution. The explanation is the HDMI was pulled from the AT&T DVR and replaced with the Chromecast HDMI. Does this mean the 3 inch dongle adapter was put in between the DVR and the HDMI cable running to the TV?  Where was the "..other empty slot"?  In the TV or the DVR?

 

The Chromecast adapter is only to provide a more flexible fit for the dongle itself. I don't see this optional item providing enhanced connectivity.  The Chromecast dongle itself, does fit into an empty HDMI slot on my TV, but that doesn't help it connect to the network.  Could you please clarify your solution?

I'm having this same problem, but I don't understand the described solution. The explanation is the HDMI was pulled from the AT&T DVR and replaced with the Chromecast HDMI. Does this mean the 3 inch dongle adapter was put in between the DVR and the HDMI cable running to the TV?  Where was the "..other empty slot"?  In the TV or the DVR?

 

The Chromecast adapter is only to provide a more flexible fit for the dongle itself. I don't see this optional item providing enhanced connectivity.  The Chromecast dongle itself, does fit into an empty HDMI slot on my TV, but that doesn't help it connect to the network.  Could you please clarify your solution?

Re: Need help connecting Chromecast to uverse router

5 of 14 (44,305 Views)
0
(0)
  • Rate this reply
View profile
Nov 15, 2013 9:15:41 PM
0
(0)
Contributor

Tried all: 

-- Mac Address Control

-- Removing Security

-- UPNP was always on

 

Nothing Worked

 

MY ROUTER SETTING

-- Default setup with default wireles key.

-- No Mac Address Control

 

Then (SOLUTION)

-- RESET chromecast by Holding the button on it for 10+ Seconds

-- Click "HERE" on the bottom of this page.

https://support.google.com/chromecast/answer/3438461

-- It worked.. like a charm.. 

 

Tried all: 

-- Mac Address Control

-- Removing Security

-- UPNP was always on

 

Nothing Worked

 

MY ROUTER SETTING

-- Default setup with default wireles key.

-- No Mac Address Control

 

Then (SOLUTION)

-- RESET chromecast by Holding the button on it for 10+ Seconds

-- Click "HERE" on the bottom of this page.

https://support.google.com/chromecast/answer/3438461

-- It worked.. like a charm.. 

 

Solved::: Chromecast Connecting Issue With At&T Uverse 2Wire Router

6 of 14 (44,143 Views)
4
(1)
  • Rate this reply
View profile
Solved
Nov 28, 2013 12:00:06 PM
4
(1)
Tutor

I had the same problem. I don't understand the reported solutions. My Gateway is Model 3800HGV. I contacted the manufacturer and got a useful response that solved my problem. I copy below the long message that I got from them. Their approach was too complicated for me to do all their steps but it turned out that doing just one of the steps was all that I needed. The critical step was to put the Gateway into DMZplus mode (whatever that is!). See highlighted  step #7 below. I still don't understand step #6 but it didn't seem critical.

 

-------------------------   Message from 2Wire suppport follows----------------------

I would recommend putting the gateway in DMZplus mode. If this works then you will know that you need to open up some ports.

In order to place a device on your home network into DMZplus mode, use the following steps:

1. Browse to http://192.168.1.254
2. Select the "Settings" in the top row of the page.
3. Select the "Firewall" tab in the second row.
4. Select the "Applications, Pinholes and DMZ" tab in the third row of the page.
5. Enter the system password for your 2Wire Gateway. (By default this is on a sticker on the side labeled "system password" or "device access code")
6. In box 1 select the device for which the firewall will be disabled
(This connection must be set to obtain an IP address via DHCP)
7. Click the "Allow all applications (DMZplus mode)" radio button.
8. Apply the setting by clicking the SAVE button at the bottom of the page.
9. Reboot the device that was placed in DMZplus mode.

If that works then I have provided instructions for port forwarding below.

To forward a port through the firewall of your 2Wire to a specific device, please follow the following instructions:

1. Browse to http://192.168.1.254
2. Select the "Settings" tab in the first row
3. Select the "Firewall" tab in the second row
4. Select the "Applications, Pinholes and DMZ" tab in the third row
5. Click the "Add a new user-defined application" link if the application you are using is not in the pre-configured list
- If the application is on the pre-configured list, skip the next 3 steps
6. Name your rule in the Application Name box
7. Select the port (or port range) you wish to open, the protocol, and any other settings specified by the manufacturer of your application
- If multiple non-sequential ports are required to be opened, add each port's information then click the "Add To List" button
8. Once all needed ports are added, click the BACK button
9. In box 1 select the device you would like to associate with the rule
(This connection must be set to obtain an IP address via DHCP)
10. You will see the new rule (Application Name) on the list on the left
11. Add this rule so it appears on the right
12. Apply the setting by clicking the DONE button at the bottom of the page
13. Reboot the device you would like to associate with the rule

I had the same problem. I don't understand the reported solutions. My Gateway is Model 3800HGV. I contacted the manufacturer and got a useful response that solved my problem. I copy below the long message that I got from them. Their approach was too complicated for me to do all their steps but it turned out that doing just one of the steps was all that I needed. The critical step was to put the Gateway into DMZplus mode (whatever that is!). See highlighted  step #7 below. I still don't understand step #6 but it didn't seem critical.

 

-------------------------   Message from 2Wire suppport follows----------------------

I would recommend putting the gateway in DMZplus mode. If this works then you will know that you need to open up some ports.

In order to place a device on your home network into DMZplus mode, use the following steps:

1. Browse to http://192.168.1.254
2. Select the "Settings" in the top row of the page.
3. Select the "Firewall" tab in the second row.
4. Select the "Applications, Pinholes and DMZ" tab in the third row of the page.
5. Enter the system password for your 2Wire Gateway. (By default this is on a sticker on the side labeled "system password" or "device access code")
6. In box 1 select the device for which the firewall will be disabled
(This connection must be set to obtain an IP address via DHCP)
7. Click the "Allow all applications (DMZplus mode)" radio button.
8. Apply the setting by clicking the SAVE button at the bottom of the page.
9. Reboot the device that was placed in DMZplus mode.

If that works then I have provided instructions for port forwarding below.

To forward a port through the firewall of your 2Wire to a specific device, please follow the following instructions:

1. Browse to http://192.168.1.254
2. Select the "Settings" tab in the first row
3. Select the "Firewall" tab in the second row
4. Select the "Applications, Pinholes and DMZ" tab in the third row
5. Click the "Add a new user-defined application" link if the application you are using is not in the pre-configured list
- If the application is on the pre-configured list, skip the next 3 steps
6. Name your rule in the Application Name box
7. Select the port (or port range) you wish to open, the protocol, and any other settings specified by the manufacturer of your application
- If multiple non-sequential ports are required to be opened, add each port's information then click the "Add To List" button
8. Once all needed ports are added, click the BACK button
9. In box 1 select the device you would like to associate with the rule
(This connection must be set to obtain an IP address via DHCP)
10. You will see the new rule (Application Name) on the list on the left
11. Add this rule so it appears on the right
12. Apply the setting by clicking the DONE button at the bottom of the page
13. Reboot the device you would like to associate with the rule

Re: Need help connecting Chromecast to uverse router

7 of 14 (43,686 Views)
Solution
0
(0)
  • Rate this reply
View profile
Dec 30, 2013 6:57:45 AM
0
(0)
Contributor

I was having many of the same problems and tried a variety of the things suggested. I finally decided that it might be some interference from my wireless access point that I installed upstairs. I unplugged the access point and then went through the set-up process again. I was able to get Chromecast installed! Now, all I have to do is figure out how to reactivate the access point without it interfering with Chromecast.

 

FINALLY!!

I was having many of the same problems and tried a variety of the things suggested. I finally decided that it might be some interference from my wireless access point that I installed upstairs. I unplugged the access point and then went through the set-up process again. I was able to get Chromecast installed! Now, all I have to do is figure out how to reactivate the access point without it interfering with Chromecast.

 

FINALLY!!

Re: Need help connecting Chromecast to uverse router

8 of 14 (40,080 Views)
Highlighted
0
(0)
  • Rate this reply
View profile
Mar 6, 2014 7:44:10 AM
0
(0)
Contributor
Were you able to find a way reactivate the access point without it interfering with Chromecast?
Were you able to find a way reactivate the access point without it interfering with Chromecast?

Re: Need help connecting Chromecast to uverse router

9 of 14 (35,380 Views)
0
(0)
  • Rate this reply
View profile
Mar 8, 2014 6:31:02 AM
0
(0)
Contributor
Yes - once I got it connected, I was able to reactivate the access point. However, the access point continues to cause some other problems, and I tend to not use it very much - keep it unplugged.
Yes - once I got it connected, I was able to reactivate the access point. However, the access point continues to cause some other problems, and I tend to not use it very much - keep it unplugged.

Re: Need help connecting Chromecast to uverse router

10 of 14 (35,243 Views)
0
(0)
  • Rate this reply
View profile
Apr 1, 2014 5:15:24 PM
0
(0)
Contributor
Only needed the first 8 steps of this answer -easier than it sounds if you're used to the router interface. Took 2 minutes.
Only needed the first 8 steps of this answer -easier than it sounds if you're used to the router interface. Took 2 minutes.

Re: Need help connecting Chromecast to uverse router

11 of 14 (33,961 Views)
0
(0)
  • Rate this reply
View profile
Jul 20, 2014 11:14:16 PM
0
(0)
Contributor

I think the instruction, "If that works then I have provided instructions for port forwarding below" after following the 9 steps to allow dmz plus may not be right. I did those dmzplus 9 steps and got connectivity. I'm thinking that if the dmzplus doesn't work, then you need the port forwarding, so the above instructions would then read "If that doesn't work then I have provided instructions for port forwarding below.", just a thought.... cause why would you need the port forwarding if the openning the dmz to the chromecast worked?

I think the instruction, "If that works then I have provided instructions for port forwarding below" after following the 9 steps to allow dmz plus may not be right. I did those dmzplus 9 steps and got connectivity. I'm thinking that if the dmzplus doesn't work, then you need the port forwarding, so the above instructions would then read "If that doesn't work then I have provided instructions for port forwarding below.", just a thought.... cause why would you need the port forwarding if the openning the dmz to the chromecast worked?

Re: Need help connecting Chromecast to uverse router

12 of 14 (29,424 Views)
0
(0)
  • Rate this reply
View profile
Aug 18, 2014 3:49:51 PM
0
(0)
Contributor

Regarding the two sets of detailed instructions,

 

I think the first one is to establish that a firewall change will solve the problem, a proof of principle, but is not best used since method 1 opens the firewall to all Apps.

 

I think the second set of instructions is the tailored approach, so as to only open the firewall to the Chromecast (in this case) but not to all Apps, once having established by method one that opening the firewall fixes the problem.

 

But since I have not used either, what do I know?

 

I cut and pasted the list of Apps that could be chosen before I plugged in the Chromecast so that I could compare it to the the list with the Chromecast plugged in, with the hope that the new item on the list will be the Chromecast ID, if for some reason it is not self explanatory.

 

Regarding the two sets of detailed instructions,

 

I think the first one is to establish that a firewall change will solve the problem, a proof of principle, but is not best used since method 1 opens the firewall to all Apps.

 

I think the second set of instructions is the tailored approach, so as to only open the firewall to the Chromecast (in this case) but not to all Apps, once having established by method one that opening the firewall fixes the problem.

 

But since I have not used either, what do I know?

 

I cut and pasted the list of Apps that could be chosen before I plugged in the Chromecast so that I could compare it to the the list with the Chromecast plugged in, with the hope that the new item on the list will be the Chromecast ID, if for some reason it is not self explanatory.

 

Re: Need help connecting Chromecast to uverse router

13 of 14 (27,753 Views)
0
(0)
  • Rate this reply
View profile
Aug 19, 2014 6:35:56 AM
0
(0)
Contributor

I stocked on step 7.
-----------------------------------------------------------

7. Select the port (or port range) you wish to open, the protocol, and any other settings specified by the manufacturer of your application
- If multiple non-sequential ports are required to be opened, add each port's information then click the "Add To List" button

-----------------------------------------------------------

what is port range for chromecast?

 

After I fhinished 9 steps on first part, it's still not working for me ><.

I stocked on step 7.
-----------------------------------------------------------

7. Select the port (or port range) you wish to open, the protocol, and any other settings specified by the manufacturer of your application
- If multiple non-sequential ports are required to be opened, add each port's information then click the "Add To List" button

-----------------------------------------------------------

what is port range for chromecast?

 

After I fhinished 9 steps on first part, it's still not working for me ><.

Re: Need help connecting Chromecast to uverse router

14 of 14 (27,639 Views)
Share this post
Share this post