02-14-2013 9:07 AM - edited 02-14-2013 9:27 AM
I posted this over at Dslreports.com but figured I would post it here too.
I was looking at the Motorola website and found this...
Lists this product as
"Motorola NVG589 Bonded VDSL 11N Gateway"
Seems to be an IPTV/Internet/VOIP modem.
Would be pointless to make a battery/modem specifically for a service that wouldn't use it, wouldn't it ?
I wonder what the ADSL2+ gateway would be then? The 5111NV? I guess if they somehow don't use this then it'll be the Pace 5168NV for both ADSL2+/VDSL2.
Solved! Go to Solution.
09-07-2013 12:36 PM - edited 09-07-2013 12:40 PM
Hello, I have one of these units with my newly installed Uverse service. I tried to set it up in Bridge mode with my Linksys E4200 running my wireless network and DHCP but couldn't make a go of it, too many issues with having trouble getting valid IP addresses for my devices after a day or so of things working. I freely admit I may have been doing this wrong.
So now I have everything connected to the NVG589, wireless and otherwise, and so far so good as far as function, but I'm used to being able to adjust a lot more settings on my Linksys routers. I even have a Linksys wireless bridge connected to it that seems to be providing a functional IP address and internet connection to my Dish Hopper satellite DVR, and it seems to be behaving well with my Linksys RE1000 wireless range extender
I do have a few questions:
1. Is there any way to program QoS settings to prioritize traffic to certain items or programs? I couldn't find this in the router settings page.
2. Does the USB port have any functionality? Will a future firmware update perhaps let us connect an external hard drive to it to share documents or stream media?
3. Is there a detailed user manual available for download online?
4. Is there any way to monitor data usage? I don't see anything in the router configuration web pages or on the att account management site, and an extended and frustrating tech support phone session didn't yield any information on how to do this. I understand my service to be capped at around 250GB per month, and while I don't expect to hit that, it is conceivable under certain circumstances for it to happen and I'd like to know in advance of getting my service throttled down to a crawl.
5. Is there a thread here or a web page that goes over optimal settings for packet filtering and all the other odds and ends? I shut all this stuff off when I was going to just pass the traffic through to my Linksys router in bridge mode but now that I couldn't make that work and have the NVG589 doing all the work I'm not sure which settings are best and which are not really necessary and might hamper performance.
Thanks in advance.
09-08-2013 2:46 PM
This is exciting news.... but opens up a ton of questions:
- Is there any way to know if the NVG589 is available in the San Jose, CA area?
- Does this new RG remove the need for external inid, meaning, can it be installed in locations such that external equipment isn't required? (For townhouses and condos, this would be a big win)
- What about Static IPs? Can the unit offer them?
- Dual VOIP lines?
And the big question..
Can it be installed without losing existing Static IP configurations?
Thanks in advance (and apologies if this is answered elsewhere -- I did look but couldn't find anything...)
10-20-2013 1:56 PM
my thoughts wrote:
You probably do not need a new RG you need a line tech, bridge tap needs to be removed, showing 2800 feet and SN less than 9 on screen shots
Unfortunately TS cannot dispatch CIM tech that I know of, instead need uverse tech.
Tech needs to run SELT test, at serving terminal,(pole or buried) if no issue on testing then issue is with drop or INSIDE wiring
If issue beyond terminal then tech needs to create outside ticket for CIM tech.
If issue is drop, tech needs to replace, if issue is bridge tap in your home then billable to resolve.
For example http://forums.att.com/t5/Features-and-How-To/Just-
Once distance and SN ratio resolved the 3801 should work just fine up to 3000 feet on a 3801 RG
Your shots show different than your statements, line issues resolve first before talk of swapping RG.
A senior tech is not aged based but employment based. Stage are T0, T1, T2, and T3 a senior tech is a T3.
Very few garages have many techs with two or more years experience, when did uverse come to your if 2010 then nobody could have more than 3 years.
By definition a T3 is someone with more than 9 months with the company who has successfully completed a required number of jobs, most are installs.
Finding an experienced repair tech is a little more challenging, need a tech work works late shift as that shift gets the bulk of repairs.
Ok i don't really know what to do.....it seems like my "line quaity" continues to degrade after each time a tech visits, they leave and my numbers look great and they fall apartover time, is there a way i can plug into the box on the house for "direct" testing and i will know its not something inbetween? I am supposedly under a thousand feet and can get the highest tiers but i am reluctant to place an order until i get the mess with the line straightened out, honestly it appeared like all was well un UVRT at one point and now its all just terrible with reds & yellows everywhere and my line distance varies based on time of day and what tv shows im watching, a single HD stream degrades things sometimes highly and sometimes i can check UVRT and have NO STREAMS of SD/HD and terrible numbers and sometimes 3HD streams and numbers are great.
10-20-2013 1:58 PM
Also can you explain what a bridge tap is and how to determine if they are in or out the home? When i had service installed they set up a appointment to send someone out to remove a brige tap that was outside at some point between my home and the pole and that was done by the only person i really trusted truly knew what they were taking about so i'd be suprised if that just didnt occur.
10-20-2013 2:49 PM
10-20-2013 2:50 PM
10-20-2013 3:22 PM
FiveOhFour - A bridge tap is another open ended pair (2 wires) connected to the service pair. At one time it was seen as a flexible, cost effective way to provide telephone service. It did not cause noticeable interference with Telephone service. It does interfere with U-verse service.
Outside can be tracked down with electrical measurements with sensitive equipment. Inside, follow the wire from the NID & look for another connected to it before it reaches the RG. Also, remove any "extra" connections at each end.
Thanks, I think the terms are often used in place of their meaning and while sure, its on me to know these things or speak up its yet another place that room is left for things to be lost in translation. The original install was done incorrectly, i believe in its simplest form basically it was done utilizing the old original drop instead of a new one, does that sound right? Anyway so I actually watched that take place and i watched a new connection fashioned from a spool that connects directly from the inid (i guess inid...the box on the side of the house that connects directly to drop?) to the RG with only a wall connector jack between them and all of that stuff including the lines ends and jacks are new. Does that eliminate any chance of bridge taps or have i misinterpreted?
10-20-2013 4:08 PM
10-20-2013 5:52 PM
10-20-2013 7:40 PM
I think you a are actually helping me over on broadband reports as well based on the user name? I don't want to be that guy especially if i am getting advice from the same group of people on both sites, i apologize. I just took a picture of my box outside & the wiring it looks like it is cat 5 directly to box and directly to RG & then maybe back out from the RG is a phone wire that also plugs into this box & feeds the houses outlets? I will say that the plastic enclosure of this group of wiring is a old bellsouth box but i wont conclude any of it is old on the inside i will let you draw that conclusion. I am tempted to rip it all out myself and force them to start from scratch at the box but i couldnt do that unless i was confident in what i was doing and i am fairly sure no one would advise me to do that. It is a single family home that we own, it is indeed brick.....most all homes are in this area actually but if that is all thats stopping them thats a terrible reason as we have a old empty box right above it and i would sign anything for anyone to drill two holes, i will drill myself if necessary.
The reason i say that is because thats what i was told and from the beginning i was told there was a bridged tap that needed to be removed and then someone came and removed that. The guy told me basically there was a single copper wire & he replaced that drop with a newer one (i guess cat 5) does that make sense? should i post a pic here or over on broadband? I am happy to get help from both places i just dont want to give you/anyone twice the work if its largely the same group of people
10-21-2013 1:27 PM
I greatly apologize about all the issues you are having with your services. I would be glad to investigate this for you further and run some line tests on our end to see if there is a possible bridge tap still present. I will be sending you a private message to gather more information so be on the lookout for one.
10-21-2013 1:52 PM
Hi David and thanks,
I am hesitant to accept your help for one reason only, there is a "social media team manager" who has been trying to help me, she spoke to the "Head tech" in my area (the manager of the other T3 techs that came out) and she was asking him to come out and he even called me on a friday and said he would try to come by and take care of me but he never called back and i just dont want the lady who has tried to help me to be "discipined" or anything like that because i have basically just stopped replying to her until I could do some research and gain some more knowledge because i finally said i wouldn't have anyone come out until i knew what i was talking about to the point i was comfortable standing my ground if certain things did or didnt happen.....are you on the same team of people as "a social media manager" who has been trying to help through twitter.....she has been very kind and while she may not know as much as many here she hasn't let that stop her from trying to help.....the only problem i have had is if i send a DM on twitter & she isnt there at that time she usually wont get it but that isnt't a big deal.
My ultimate goal is to get the lines straightened out so that i can give y'all more money and upgrade to the power tier. One issue i have is poor communication among various employyes and departments, when i was first sold service a master linesmen and corporate u-verse tech came out and made measurements etc. & offered me a "pilot program" to test out "faster service than i can currently get" but something screwy happened & no one else knew what i was talking about and i could never reach them at the cell number i had.
10-21-2013 2:12 PM
I am not part of the same team as that individual, but we are all here to help each other. It sounds like she is actively doing everything she can to ensure your issue is resolved. If you need any further assistance, whether you just need someone to step in, or just help with a general question, don't be afraid to ask, and I will be glad to assist.
Welcome to the internet boards! Check out our troubleshooting articles below and don’t forget to search the forums - your question may have been answered already!
Service acting up? Click here to troubleshoot now!
Do you have questions about Internet and Email Security? Have them answered on Wednesday, April 26th at our Knowledge Sharing Session: Hack Attack!