04-04-2012 2:07 PM
I just switched from Comcast to AT&T and my Kodak printer which has worked flawlessly up till now, CANNOT connect to my wireless network. Kodak says it's AT&T's problem and AT&T says it's the printer's problem. So guess what? Nobody has to take any kind of responsibility AT ALL. AT&T "generously" offered to help solve the problem if I wanted to pay an extra $15 per month for TECH SUPPORT! I'm paying $50 a month for internet service and ALREADY paid $95 to set the thing up, why do I have to pay anything else to get it set up RIGHT? I've spent a total of 6 HOURS on the phone with both companies trying to solve this problem, when I could have been working on projects and making money. So far the problem has cost me $450. I should have stayed with Comcast.
Can anyone out there help me get my printer working again? Does anybody at AT&T even give rat's a$$?
Solved! Go to Solution.
04-10-2012 11:55 AM
I apologize your having issues with your Printer. Please tell me what kind of router you are using so I can assist you in fixing the issue. It sounds like you need to change the wireless settings to your new router if it's a new Gateway.
06-23-2012 5:43 PM
While I have not spent as many hours or money trying to get my Kodak printer hooked up to the wireless network, I am frustrated because I just switched to AT&T and can't seem to get any help with this problem.
I have a Kodak All In One printer that won't recognize the AT&T wireless network. I am using UVerse. I believe the router is an AT&T UVerse router.
06-28-2012 10:44 AM - edited 06-28-2012 10:45 AM
Sorry to hear you are having this problem. Most likely the wireless security settings need to be changed. Try using this link to resolve your issue. The 2wire wireless key is located on bottom or side of router near the barcode.
Please let me know if you have any other questions.
11-27-2013 11:30 AM
After much searching on the web, I found one person who seems to have figured this out. Following are the instructions I found and I've hilighted the steps I actually completed to successfully connect my Kodak All-in-One to my u-verse gateway/router.
As for connecting to ATT router these are the steps I followed.
Using your Kodak All-in-One Printer:
1) On Kodak printer scroll to network settings and select
2) Select View Network Configuration
3)scroll down till you see MAC: xx:xx:xx:xx:xx (write this Mac code down, or take a pic)
4)I you will also need to locate and write down the router http:, System Password and Wireless Network Key (located on your wireless router). This will save you time running back and forth between your computer and router.
Using your home computer
5)Log into your router http should be something like 192.168.1.254, Logging in requires the System Password not your network key
6)Select Settings via top tabs
7)Select LAN directly below the Settings tab
8) Select Wireless in next row below the LAN
9)Scroll to bottom where you will Find MAC Filtering. Select Edit Blocked/Allowed Device List
10) Select Enable Mac Filtering then Save. There should be a check mark in the enable box
11) Enter your MAC address that you had previously written down.
12) After Entering and selecting Add to List, your MAC address will either pop up in Allowed Devices or Blocked Devices. (Mine showed up in Allowed Devices after I entered it in.)
13)If MAC address is showing in Blocked Devices, select your Mac Address from blocked list and press the [<<] button to move it to allowed devices.
14) On the same tab where you selected Wireless, now select DHCP
15) Write down the Router Address, Subnet Mask, First and Last DHCP address
Back to Printer
16) Orn your pinter under Network Settings, Select Advanced IP Address Setup
17) Select Manual(Static)
18) The first set IP I put in The Last DHCP address from the picture taken above; something like 192.168.001.253, (make sure third is .001 eventhough it says .1)
19) The second IP Address I put in the Subnet Mask
20) The Third and Fourth IP Addresses I left as all Zeros.
21) Go back to Network Settings and try to reconnect to your router. With any luck it will hopefully connect. Good Luck and I hope this helped.
12-03-2013 10:50 AM
Wow, thank you so much for your contribution, it's very helpful and I'll mark it as a solution so other users can find it easily.
Did a post have a solution that worked for you? Help other people find solutions faster by marking posts that helped you as an "Accepted Solution". Learn about accepted solutions: Learn More.
Welcome to the internet boards! Check out our troubleshooting articles below and don’t forget to search the forums - your question may have been answered already!
Service acting up? Click here to troubleshoot now!
For DSL related issues. We highly recommend chatting with our teams to address this as quickly as possible.
© 2017 AT&T Intellectual Property.This link will open a new window All rights reserved. AT&T, Globe logo, Mobilizing Your World and DIRECTV are registered trademarks of AT&T Intellectual Property and/or AT&T affiliated companies. All other marks are the property of their respective owners.
Congratulations! You earned the Liz badge!