tommy99's profile

Mentor

 • 

62 Messages

Thursday, January 26th, 2017 4:30 AM

Could my internet issues be a bad Motorola NVG589 Modem?

Hi,

 

I've come to realize that my home issues with the internet could be a bad Motorola NVG589 Modem. The reason I say this, every few hours online, I get the browser window saying "more information is needed' and it is the ATT modem front page saying "no internet connection" so i check the modem leds and sure enough, only power/ethernet/wireless are lighted, broadband is red, service/phone are out. I can wait it out (maybe 10 minutes and the modem comes back on with internet access. But the quicker route is to power cycle the Motorola NVG589 Modem. I've turned off ipv6 as suggested from previous posting. Each time the internet goes out, I use my mobile app ATT Mark the Spot to send the issue. Out of the few dozens of sending to ATT, only once did it respond with "we are aware of a local problem and are working to fix" but all the other times, nothing.

 

So my question to anyone, what is the process of getting another Motorola NVG589 Modem to see if that is the issue? Can I get an "off the shelf" modem to test against? The problem with the Off the Shelf modem is I need to find one that has a phone line.

 

Thanks,

A frustrated uVerse customer

Accepted Solution

Official Solution

Employee

 • 

18 Messages

2 years ago

A red Broadband light is often an indicator that your gateway is not detecting a DSL signal. A few things you can do are to check to see what the Gateway Status Lights mean. You can resolve most issues by Restarting Your AT&T Gateway.

We also have an article with more information on Issues with Blinking Red Broadband Light.

Thanks

ATTJohnCS, AT&T Community Specialist

Accepted Solution

Community Support

 • 

6.7K Messages

7 years ago

Hi @tommy99,

 

We are sorry about the issues you are having with your service. We are looking into this issue, and we are hoping that a reboot now will be able to get the issue corrected. Here is an article that goes over how to do it properly. If you do have a battery unit, be sure to remove it before doing the reboot. Let us know how it goes.

 

-ATTU-verseCare

Contributor

 • 

1 Message

7 years ago

My U-verse ARRIS NVG589 has been working flawlessly over the last 3+ years until earlier this week. The broadband light stayed lit but the Ethernet light kept blinking (and there was no internet access).  This happened after my kids served the web which may just have been a coincidence.  I rebooted my wireless router (ASUS RT-N66R) and a never-seen-before Windows Security "Microsoft Edge" dialog box appeared requesting the ASUS router's user name and password (I am running Windows 10) which I entered with hesitation.  I still did not get Internet connection until I also rebooted the NVG589.  Now I have access to the Internet but am unable to access the NVG589 after entering the NVG589 IP address (http://xxx.xxx.x.xxx) that appears on the cover of the unit.  The error message reads "This Site Can't Be Reach".

 

Questions:

1.  How do I regain access to my NVG589 gateway admin page?

2.  How likely is it my ASUS wireless router and/or the U-verse NVG589 is hacked/hijacked?

 

Thank you.

 

 

Professor

 • 

2.2K Messages

7 years ago

@im2bz2p

Flashing Ethernet light is normal.

 

Never use Microsoft Edge as it has countless issues regarding reaching sites. It's a poor attempt to protect users. Download either Firefox or Google Chrome. Try with either of the two browsers and advise.

Contributor

 • 

1 Message

7 years ago

Can't connect to the internet

Contributor

 • 

1 Message

7 years ago

My att Uverse gateway has cut out and rebooted approximately 20 times in the past month.  The gateway reboots within a few minutes but this creates an untenable situation when my son is taking a test for his online college course that he cannot restart.  To be clear:  when this happens the internet goes completely out as well as the Uverse TV programming.  This cutting out has happened as frequently as daily for 5 days in a row.  Sometimes I have to reboot our receivers and other times they come back on when the gateway resets.

Professor

 • 

2.2K Messages

7 years ago

@Msgreen904

What type of AT&T provided equipment do you have and what is the status of all the lights?

Does the WiFi connect?

What type of device are you trying to connect with?

Has this ever worked?

Professor

 • 

2.2K Messages

7 years ago

@spbmullin

Very likely either a router/gateway or circuit issue. Contact AT&T for service.

@ATTDSLCare @ATTHelpForums

Teacher

 • 

12 Messages

7 years ago

Gear: 

3800HGV modem as NAT router  (cat5 to netgear R6250)

Netgear R6250 AC as access point and gigabit switch (cat5 to Arlo hub, SmartThings hub, another gigabit switch in basement)

Trendnet Gigabit Switch (cat 5 to SmartTV and blu ray players)

Arlo cameras

SmartThings

Lots of ipads/laptops/cellphones/etc

 

My family has been complaining about "wifi" for couple months now.  Some if it is just the ipad games they are playing, glitches on game servers or whatever.  But I have also observed times where our internet service has just stopped.  On my ipad I see a spinning icon at top, left side of status bar when this happens I think.  When things are working okay, Ookla(?) speed test app reports we are getting close or better than our 6Mbps speed, 30ms ping. 

 

Last week called AT&T, they decided to send me a new modem (5268AC) since I was driving and couldn't debug with him.  I couldn't get it to install so they sent a AT&T rep to my house couple days ago.  He said since I have coax from outside to my 3800HGV, that the 5268AC wouldn't work like that.  It needs ethernet for the feed from outside, then coax to TVs only (I may be mis-stating a bit).  I decided to hold off on that so he offered to check signal and make sure all connections and splitters were good.  Also he sees no issues/errors with the 3800HGV so sticking with it for the moment.

 

Then last night observed a dropout, speedtest on ipad was really low like 0.1Mbps, web pages wouldn't load.  I was 5 feet from wifi Access Point.  No other devices actively gaming or streaming video (could have been smart home device traffic or devices in standby refreshing).  Unfortunately I forgot to check an ethernet hard wired computer at time this was happening to rule out wifi issues... I turned off 3800HGV wifi couple weeks ago, didn't help (I have had the a Netgear in Access Point mode for 1.5 years).  Turned off Arlo camera hub for a week, didn't help.

 

So how can I debug this further?  AT&T tech thinks I need faster service and while I agree that 6Mbps isn't enough to handle multiple audio/video streams and games and everything all at once... we have survived fine with that and I am already paying AT&T WAY too much every month for internet, tv + 2cellphones.  Plus I am confident these dropouts have happened at times when there wasn't high bandwidth usage.

 

Are there any logs in the modem I can access that would show errors?  Any other advice?

 

 

ACE - Guru

 • 

986 Messages

7 years ago

When these things happen it's important to test using an Ethernet connected device.

Sounds like you have a lot going on there. It could also be the way you have linked the RG and your R6250.

Also,  Using a smart phone load the the myatt app.

 

Next time you have an issue, access the app, sign in with email/password, about 6 lines down, run the Fix It Now portion.

This will run a total of 4 (no Uverse TV service) or 5 (Have Uverse TV service) test.

Walks through some basic troubleshooting, and if problem not resolved assists in creating a service ticket.

Not finding what you're looking for?
New to AT&T Community?
New to the AT&T Community? Start by visiting the Community How-To.
New to the AT&T Community?
Visit the Community How-To.