10-30-2018 9:12 PM
I put my router behind the PACE gateway and set the router as DMZ. The latest firmware is crapping out my fiber connection where I'm only able to get 50mbps down and 1-200 up. I thought it was my router crapping out, but apparently when I connect any other device directly to the gateway, I'm able to pull 940mbps up and down. I swapped an older router and placed that device in the DMZ And it starts acting up and the previous router started working normally.
Can someone look into this?
Solved by: Go to Solution.
11-20-2018 7:35 AM
Add me to the list of having this problem. On Business Internet 50 and the update got pushed to me after a reboot. 5268 -> ERX through DMZPlus+. I get around 45 downish instead of the nice 55 when directly connected to the RG.
11-20-2018 1:38 PM
Same here. I'm subscribed to 100/100 service and receive that when connected directly to RG, but with my own router in DMZ mode, I am getting 50/100 speeds.
- edited 11-20-2018 8:14 PM
Same here. pfsense connected to 5268AC only getting 40/200. Unplug pfsense and plug computer into 5268AC I get 950/950. The weird thing is I have OpenVPN setup on my pfsense if I use OpenVPN I get 500/200.
11-20-2018 3:00 PM
I'm continuing to receive a lot of private messages from you all providing your account details, locations, and setups - I can't thank you all enough!
I don't currently have any updates, but wanted to let you all know that we're actively working on a solution and are hearing you all loud and clear.
By posting that you have a problem, and reporting this with the level of details that you have, we'll continue to get closer to a speedy resolution.
11-20-2018 5:33 PM
Also more than happy to help debug. Seeing the exact same issue ... have a Ubiquiti infrastructure behind the Pace, had it working great with DMZplus (~940 symmetric) until the update. After the update, my everyone in the house had AT&T Wifi calling failing on our iPhones, and had the 50/200 behavior others identified. After beating my head against this for hours (lots of tcpdumping, watching flows, rebuilding my edge router, etc) I finally swapped out the router, and everything was working great. As a last step I went into the RG and set DMZplus and suddenly it all was back to the failed state.
What information can we PM you that would help?
11-20-2018 6:24 PM
@ATT Kevin - Another affected user. just noticed the reduction in speed about a week and a half ago. am running 220.127.116.111418-att firmware on my 5268AC. Thought it was my router (AC68) had not tried taking it out of DMZ plus mode as I have some port forwarding set up on it that I don't feel like recreating on the Pace.
Hate to see this get passed the QC, but hopefully now that ATT is COMPLETELY aware of the issue we can get an updated firmware pushed out.
1) Possible to roll back to the previous firmware? How would a customer do this?
2) Can tech support push out patched firmware when its available when customer calls, or do we just have to wait for it to cycle through?
I'm paying for 1000/1000 and only getting 50/400 at best on most days, because of an issue with AT&T equipment. Sure I could just use the Pace but thats not the point and the experience of using the PACE is not the same as using how I traditionally have my network configured behind the Asus. If we contact customer service is there another gateway that DOESN'T present this issue that we can specifically request and get? Guessing we can't just visit an AT&T store to swap this out?
11-20-2018 7:11 PM
I will also note, my current workaround has been using older firmware on my 5268AC, which is getting me 700~ down/500~ up at the moment with 9-15ms ping.
On the latest firmware with DMZ+, I was getting 50/200 with 13-15ms ping.
Before this issue, in the first weeks after my initial Fiber 1000 install, I was getting 800/800 with 1-2ms ping
11-20-2018 7:46 PM
@ATTKevin - thanks for looking into this. I've been beating my head against a wall trying to figure out why my speeds went from a steady 800-900 up and down to 45-50 down and 100ish up on 11/11. Someone on Reddit pointed out the firmware issue and I'm in the exact same boat.
Spoke with customer service today and they are sending me the NVG599 so maybe that will solve my issue but I'd really like to see a fix from AT&T on the Pace gateway as well. It's really frustrating as a customer to suddenly wake up to this one day. Appreciate your help in looking into it though.
11-20-2018 8:18 PM
Add me to the list of DMZ+ users with sudden crap-out on Pace 5268AC. 11.01 firmware. I will be reaching out to support tomorrow.
11-20-2018 9:49 PM
I'm having this exact same issue as well. Been running pfSense on DMZ+ for years with full speed; now it's capped to 50 down/200 up. Put it in NAT mode and it gets full speed again.
Tried directly with my laptop and it behaves the exact same way.
11-21-2018 12:15 AM
This is exactly what was happening with my eero network behind my Pace. I would get calls with WiFi Calling and people couldn’t hear me. Thank goodness I found this. I was going crazy.
- edited 11-22-2018 2:00 AM
I would like to add myself to this list as well. I literally stayed up last night trying to figure it out. I thought my Asus router (RT-AC68U) was crapping out on me. But then discovered the bug with dmz mode. Setting dmz mode creates a cap of around 50/200 with out I get 950/950.
Edit: I tried to downgrade and it completely screwed up my gateway. I can no longer reset it, the connection is very intermittent and I can’t access the gateway. Called support last night and they will be spending me a new gateway.
Visit these related resourcesView New Device Help!