What is happening with 3G?
Frogis's profile

Tutor

 • 

3 Messages

Wednesday, May 14th, 2014 5:06 AM

HELP - 3G light is flashing, microcell was previously working fine

Hello,

 

   I figured it was worth posting here so I have yet to have success with anything else. 

 

Background

 

I live in an area almost exactly inbetween three AT&T cell phone towers, so subsequently my phone is constantly switching singnals from one tower to the other giving me very inconsistent service.  After diagnosing the problem with AT&T about six months ago they sent me a micro cell free of charge, and it worked absolutely fantastic until....

 

The Problem

 

About a week ago my microcell's 3g light started flashing, this had happened once or twice before so I performed a simple reset but it did not fix the problem like before.

 

  •   I tried resetting my modem, router, and microcell
  •   hard resetting my microcell for 30 seconds
  •   de-activing and re-activating my microcell twice
  •   checking my power cord to make sure it was the right voltage
  •   getting a replacement microcell sent to my house
  •   setting up my microcell in the alternate arrangement (modem-->microcell-->router)
  •   updating the firmware on my router

and none of these fixed the problems.

 

My current internet is about 30mbps DL and 10mbps upload so that isn't the problem

The ports on my router are all opened, and nothing has changed to effect that

 

After going extensively through the forums I am kind of at a loss of what to try next.  Any suggestions from people on the forums?

 

I am currently located in the East Bay of California (Alameda, CA)

 

Thanks very much.

 

-Frogis

 

 

Accepted Solution

Official Solution

Community Support

 • 

15.2K Messages

8 years ago

Hello Community!

 

One of the most common topics we see on the forums is regarding the Microcell.  Specifically, how to identify and understand the differences between the LED light indicators on the device as well as troubleshooting steps to resolve any issues.

 

The information contained below is a combination of the great community content, as well as information provided by our Advanced Technical Support team that supports the Microcell every day.

 

MicroCell LED Guide

 

Power LED

  • Off– No power to MicroCell.
  • Solid Green– Microcell has power.
  • Solid Red– MicroCell is either still powering up or is in an error state. Please unplug the MicroCell from power and plug it back in. If the LED remains red, please try an alternate power outlet or alternate power cable. You can also test the ac adapter with a voltmeter. It should read 16VDC ± 0.5. If not, replace the adapter with one of the exact same power rating.

 

Ethernet LED

  • Off– No Ethernet cable connected. Please make sure both sides of the Ethernet cable are firmly attached. One side should be plugged into the Ethernet port on the MicroCell and one side should be plugged into an Ethernet port on the modem or router. Ethernet cables should click when inserted into an Ethernet port. If the LED does not light when both sides are firmly attached, please try an alternate Ethernet cable. The MicroCell has been tested and works with Ethernet cables up to 15 feet long.
  • Solid Green– The Ethernet cable is connected and the MicroCell has been assigned a valid IP address.
  • Flashing Green– The Ethernet cable is connected but the MicroCell has not been assigned a valid IP address. Please power cycle the modem, then router, then MicroCell in that order. If the Ethernet LED continues to flash, please ensure DHCP is enabled on the modem or router. The MicroCell requires DHCP to work.

 

GPS LED

  • Off– No location check is being performed at this time. The MicroCell is either unplugged or is going through activation.
  • Flashing Green– The MicroCell is performing a location check. It is scanning both for GPS satellites and for local cell sites.
  • Solid Green– The MicroCell has completed the location check.

 

Computer LED (only on white model MicroCells)

  • Off– Nothing is plugged into the computer port.
  • Flashing Green– Traffic is passing through the MicroCell.
  • Solid Green– No traffic is passing through the MicroCell.
  • If continued issues occur, it is recommended to not use the Computer Port because of potential issues with the connected computer’s internet settings.

 

Network or 3G LED

  • Off– The MicroCell is not activated. It is either powered off or going through activation.
  • Flashing Green– The MicroCell is not activated. It is going through activation or is experiencing a connectivity issue. Please wait 90 minutes after registration. If the 3G LED continues to flash after 90 minutes, please review the Firewall & Router settingsand make sure the modem or router are appropriately configured for use with a MicroCell.
  • Flashing Red– The MicroCell has failed the location check. Please ensure the MicroCell is registered to the correct address. Please power cycle the MicroCell to trigger a new location check. It may also help to relocate the MicroCell to a location with a clear view of the sky. If the MicroCell fails the second location check, please contact AT&T Customer Care.
  • Solid Green– The MicroCell is fully activated and is broadcasting signal.

 

We also have comprehensive Video content to help you navigate any issues you might be having:

 

Note: A failing AC adapter can affect any of the LED lights so it’s always a good idea to check the adapter with a voltmeter, especially if the MicroCell is a few years old or you have experienced numerous or unexpected power outages.

 

You can also find a full list of Microcell support by visiting our Microcell support site

 

Thanks again for all your fantastic questions and support, and please comment below if there is anything we’ve missed!

 

Katie, Community Specialist

 

Voyager

 • 

2 Messages

10 years ago

I've been a MicroCell user for the past several years, and up until a few days ago, have never had any issues; but now, my MicroCell is unable to connect to the network.

 

The situation right now is that the top three status lights (power, ethernet, gps) will all light up solid green, while the bottom light (3G) flashes green and never solidifies.

 

Deactivating and reactivating on the website results in power up, software update, and location verification all completing successfully, but activation failing with FTC101.

 

Rebooting modem/router does not help, nor does restoring factory default settings, nor direct connection between MicroCell and modem bypassing router.

 

Disabling firewall on modem and/or router, enabling static NAT/single static IP address, and DMZ, does not help any, although the MicroCell was operating correctly in the past with no changes made from the factory default settings, so I wasn't expecting any of that to help much.

 

I took the MicroCell into town with me, and after changing the address, tested it on the DSL connection at my business with the exact same results.

 

I called AT&T tech support while there, explained all of the above, and they authorized a replacement.

 

I exchanged the MicroCell at the AT&T store in town and took the replacement back home with me to start over, and unfortunately, the replacement behaves identically to the original.

 

Attempting to communicate with support while at home has been problematic, as my phone is completely unusable without a working MicroCell; but I have been able to use Skype to contact them a few times, and have heard from them that the specific part of the activation process which is failing is when the MicroCell attempts to to establish the VPN connection.

 

I have contacted CenturyLink regarding the ports the MicroCell utilizes, and got the response that their policy is to not block ports as they do not want to break user applications, although they didn't actually answer the question about those specific ports.

 

Both of the internet connections I have tested on are provided by CenturyLink, I have no idea what that says about their answer.

 

At this point I really don't know where to go next from here, and would greatly appropriate any help or advice.

Teacher

 • 

20 Messages

10 years ago

Otto,

 

Could you provide AT&T's server IP's used to establish the VPN tunnel?  A tracert would help to troubleshoot originating from the clients' end.

 

I know that Verizon supplies their IP addresses used for their femotocell, which I have used to troublehsoot several issues.

 

If nothing has changed at the customers house, it's either their ISP (Which I doubt they are blocking the necessary ports), routing, and/or AT&T equipment.

 

If EnigmaWave could perform a tracert to their servers, we could dig a little deeper to try to uncover the issue.  I did a quick search and I couldn't find any IP's, except for your .pdf that shows an IP address, with the first 3 octets masked out.  Not sure if that's an option.

Contributor

 • 

1 Message

10 years ago

Had very similar problem.  Blinking 3G green light with other 3 lights solid green.  Went through all the troubleshooting with same results.  AT&T sent me replacement Microcell tower and still having same problem with replacement unit.  Have had my ISP out to check the cable and it is fine (30+MBS download). Best I can determine is there have been no software updates pushed to modem or routers in the house.  

ACE - Expert

 • 

23.9K Messages

10 years ago

fraggboy  -  the reason I x'd out the ip address is that I didn't think it was a good idea to post the address that was being used at the time I found the information. It's not secret but it does take a lot of digging to find and I don't think it would be that useful anyway to the enduser. The AT&T engineers need to verify for themselves what, and where, the problem is before they act on it. I'm not trying to be apologetic for AT&T but just realistic. Besides, that address was acquired a long time ago and it wouldn't surprise me if AT&T hasn't changed it since then because of security and other reasons.

 

NeptuneX - I will forward your complaint to the Admins but I would suggest sending a pm to CustomerCare (link in my sig) with your issue, how long it's been going on, your setup (including ISP), account information, the best way for them to contact you, and most importantly, your location. It has been my experience that ISPs are reluctant to tell customers if they've been doing any upgrades on their network boxes because quite often that doesn't require a system update to the enduser and is very transparent. Speed is only one small factor in a successful VoIP connection. A lot of things have to play nicely for your calls to make it troublefree to AT&T, especially when traversing a non-AT&T network.

Former Employee

 • 

4.9K Messages

10 years ago

Hello, everyone!

 

It sounds like you're all having issues with your MicroCells. As OttoPylot suggested, we'd be happy to look into this for you guys, so please click here to send us a private message.

 

In your message, please provide your name, phone number, email address, and the best time to reach you. You can expect a reply within two business days, so keep an eye on the little blue envelope icon in the top right corner of your screen.

 

In the meantime, feel free to message me with any other questions or concerns.

 

-Mariana

ACE - Expert

 • 

23.9K Messages

10 years ago

Thank you Mariana!

ACE - Expert

 • 

23.9K Messages

10 years ago

I'm south of you in San Jose and haven't had any issues. What is disturbing is that similar issues have been reported for the last few weeks elsewhere but the West Coast. Who is your ISP?

 

Send a PM to CustomerCare with your issue, what you have done to fix it, your account information, the best way for them to contact you, and your location. I've been working with the Admins and they are aware of this.

 

I have copied and pasted your message and sent it to the Admins.

Former Employee

 • 

4.9K Messages

10 years ago

Hello, Frogis!

 

Thanks for posting. As OttoPylot suggested, we definitely want to look into this MicroCell issue for you so click here to send us a private message.

 

In your message, please provide your name, phone number, email address, and the best time to reach you. You can expect a reply within two business days, so keep an eye on the little blue envelope icon in the top right corner of your screen.


In the meantime, feel free to message me with any other questions or concerns.

 

-Mariana

ACE - Expert

 • 

23.9K Messages

10 years ago

Thanks Mariana.

Not finding what you're looking for?
New to AT&T Community?
New to the AT&T Community? Start by visiting the Community How-To.
New to the AT&T Community?
Visit the Community How-To.