Tutor
•
11 Messages
Cisco wireless receiver known issue with playback of recorded content
The wireless STB has a known issue that T needs to address. When viewing recorded content, either SD or HD, the message "Press OK to See Your Recording" appears about every 5 minutes in a white box at the bottom of the screen. The only way to rectify is to press OK, which brings you to the recorded content menu. You then have to select the show you are watching and press Resume Play. Im returning this box for a refund.
ragcat612
Tutor
•
5 Messages
12 years ago
OK, after a month of the same problems everyone else is describing, after numerous phone calls and TWO techs coming out, after replacing the box and the WAP, and the patch cord, I just completed an on line chat with a tech support rep, and was told that there is an upgraded box with added firmware available. It is being shipped to me this week. I asked why no one else mentioned this, as I also did a "disaster recovery" on Friday. and when was this new box made available. He said he did not have that information. I specifically asked if the NEW box will be different than the previous two, and was told YES. I cannot wait for it to come. It makes sense that this has been the root problem all along. This gives me hope, but we shall see what happens.
0
0
FormerWillyb
Mentor
•
89 Messages
12 years ago
Curious about the signal strength, I used two pieces of information I've gathered over time.
1. Sometimes things that shouldn't work, do anyway.
2. The regular STB has an RJ45 jack. If the STB is connected to the system via coax, then that Ethernet port functions as though part of a network switch or hub. I've used it in the past where I had a weak wireless signal to a Roku box. It will also work if you have a Blu-Ray player with built-in streaming but without wifi. You just connect the Ethernet port on the Blu-ray player to the RJ45 connection on the back of the STB.
So...I decided to try connecting my WAP to the RJ45 port on the back of my kitchen STB, which happens to be on the other side of the same wall as our "big" TV and wireless STB in the living room.
First thing I noticed was five bars on the wireless STB. Considering that the WAP was only about four feet away, albeit on the other side of a gypsum and travertine wall, I would hope the signal was good. So I tried playing back a two hour program on H2. Since I was doing something else, I just started it and muted the sound. Every half hour or so, I came back to check on it.
Previously, within 10 minutes or so, but always within half an hour, I had the bar at the bottom of the screen with the dreaded "Press OK to browse..." This time it played all the way through without the bar. Last night, watched a one hour recorded program. No problem. Tonight, watched another one hour program. All the way with no problem.
My conclusion? If you can get the WAP close enough that the signal is very strong, the wireless STB works just fine playing back from the DVR. Question is, if the WAP has to be within four feet of the wireless STB, then what's the point? I'm going to look into the new version of the wireless STB, but this will do for now.
0
0
ragcat612
Tutor
•
5 Messages
12 years ago
After another SNAFU with a wrong address issue, the "new" box was finally delivered today. Honestly, was not expecting a miracle, and, SURPRISE!, didn't get one. Same issues, same problems with box #3. Spoke with tech support, again, re-booted the RG, changed the frequency, etc. to no avail. I am pretty close to giving up on the wireless box, but it will be a major hassle to go back to cable the way my TV is mounted. I don't know what else to do at this point. Any suggestions??
0
0
hutchk
Contributor
•
1 Message
12 years ago
I've had this same problem since my install in early January. Signal strength is not an issue. I have a direct, line-of-sight view of the transmitter about 15 feet away.
Has AT&T mentioned anything about a firmware upgrade for the current STBs?
0
0
texasguy37
Expert
•
14.5K Messages
12 years ago
Yes, I saw a post on the U-verse Facebook from another customer who has the same issue. He was contacted by someone from AT&T who indicated that this is a known issue and a firmware update is being created. No ETA was given for the release of the update.
0
0
ragcat612
Tutor
•
5 Messages
12 years ago
MY "new" box, the 3rd box, was supposed to have the upgraded firmware, according to the agent on my on-line chat. If it did, it still doesn't work correctly. It's difficult to believe ANYONE at this point. But I am still not ready to give up.
0
0
texasguy37
Expert
•
14.5K Messages
12 years ago
As far as I know, there is no updated firmware available. The current firmware version on wireless boxes is 2.0.1047.45.
0
0
sammyboy405_1
Mentor
•
35 Messages
12 years ago
0
0
verynate
Teacher
•
23 Messages
12 years ago
0
0
FormerWillyb
Mentor
•
89 Messages
12 years ago
0
0