I am trying to port forward my camera with a ddns server.  I have the port forwarding on and the dmz. I have rebooted multiple times and resetting the router.  However when I go to http://canyouseeme.org/ the ports are never open.   Even odder if I go to whatsmyip and http://canyouseeme.org/, they h

Here goes;My NAt type is strict, the pace 5268ac does not allow me to access pinholes and dmz settings. UNLESS, i factory reset it and unplug the internet in ethernet cable. Upon doing the factory reset with data cable unplugged i can access all the options the pace 5268ac should have. I did this an

Hello, decided to make a post about this, because I've been unable to figure it out after all these hours haha.My issue is simply this. Trying to port forward on the Mifi ZTE MF923.Watch the video. I show how it is supposed to work and that it doesn't and then I switch over to my normal router and i

Ok,   I'm trying to set up a recent B210 GW to allow L2TP/IPSec VPN to a VPN server behind the gateway.  Now, in one install I've enabled IP forwarding passthrough to a second firewall/router behind the gateway and then configured that firewall to pass traffic to the VPN server.  Works fine except f

I followed the instructions in http://www.att.com/esupport/article.html#!/u-verse-high-speed-internet/KM1010270 and set up a computer with a web server on port 8090.  If I enter http://192.168.1.21:8090 the web page displays inside the LAN. I created an entry for the user defined application which i

Setup5268AC to Asus RT AC-66 via LAN cable.The server that runs Plex is connected to RT AC-66 via LAN cable.RT AC-66 is in pretty much default configuration. So I've been using DMZplus mode and was perfectly happy. But seems like new firmware has some speed issue with DMZplus mode. I was getting fra

Back in 2002 When "Return to Castle Wolfenstein" enabled people to set up a server life was good....I pine for those days. I have screwed around with this Pace 2 wire and although I can get a server going. It will only successfully open my internal lan ip address. I have even used Various port ch

So my Xbox One has had Moderate Nat for the past few weeks since we’ve got this new ATT modem (BGW210-700) is the model. And i followed direct instructions that were said to work for other people, but didn’t work for me. After forwarding ports 3074 UDP/TCP, 3544 UDP, 4500 UDP, 500 UDP, 53 UDP/TCP, 8

Can anyone help troubleshoot this? I am using ip forwarding to give my beefy router the public IP address and it was from my previous location so all port forwarding is correct, I also forwarded everything in the new AT&T router. It is an arris one for gigabit internet. Connecting to a VPN solves th

I have an ARRIS BGW210-700 at home and setup Port Forwarding for my home web server. The port forwarding works normally for external requests, but not for internal requests.   Use case 1: I want to visit the home web server (192.158.2.197) from internal IP (192.168.2.150). I confir

Anyone else have problems with Port Forwarding for RDC?Is a dedicated IP required?

Hello, After reading all of the recent comments related to port forwarding issue on this appliance(5268AC), I still don’t seem to understand if there is any solution. Can someone clarify if there is any way to make the ‘pinhole’ concept work to avoid using the DMZ/Bridge to personal router as worka

Before I purchased my ATT Home Base (ZTE Z700A), I had confirmed with multiple AT&T employees that it would do what I would like to do:I would like to enable in-bound connectivity & NAT for Remote Desktop (using either TCP/UDP 3389), HTTP, FTP, and a few other ports for various services. The options

It worked when I tried the instructions described for NVG510!Use this link and follow the same instructions to setup your port forwarding for NVG589 http://portforward.com/english/routers/port_forwarding/Motorola/NVG510/QSee_QT4_DVRs.htm

I have the wireless internet homebase mf279.  I’m trying to set it up to have an open NAT on my Xbox.  I have it hooked up straight to my Xbox through the Ethernet cord provided.  I have tried port forwarding, enabling uPnP, and also tried putting my Xbox IP address into the dmz mode on my routers s

Our 2Wire set up has worked fine for a few years.  Due to rcent problems with pixelation and no on-demand service, a tech came out and replaced all the equipment with the NVG589.  That actually made everything - TV, Phone and internet - not work, but fortunately we found a "street team" guy (as oppo

My U-Verse service uses an Arris NVG589 modem with firmware version 9.2.2h3d14.  I am trying to forward port 22 for secure shell (ssh) to a Unix machine and the modem is giving me the following error:   (22) port range conflicts with reserved port (22)    I am using the prede

I have a white MicroCell that was used on another account, in the same house(family). The MicroCell has been deactivated from the previous account and added to mine. I am receiving a location verification error.Over the past two weeks, I have been in contact with AT&T 5 times. The first three times

Hi! I'm new to the forums, don't judge. I'm trying to host a Minecraft server on my computer, and I'm trying to get port forwarding working (I don't want VPN). I have all the settings configured, but there is another setting that seems to be mandatory called LAN port. I am assuming that it means LAN

We have Uverse Gigapower using an ARRIS NVG599. I have port forwarding setup for port 8080 to point to a specific machine. When I attempt to telnet to this port, the connection is refused. When I run an external port scan, it shows closed, which they define this as the port is responding but nothing