Hi, I have ATT ADSL internet service (50/5Mb package) worked fine for about last 2 years. For the past month however service keeps dropping after a few hours. Seems to be related to amount of usage with light or no usage will stay up about 12 hours, if I am streaming or downloading it stops after 2-

After posting, I realized that this is the wrong place for this question. I created a new post in the "Fiber Equipment" forum. https://forums.att.com/t5/AT-T-Fiber-Equipment/GigaPower-Has-anyone-had-success-getting-AT-amp-T-to-give-them/m-p/5295844#M3809

Hello, Here is my system configuration:I have a 3-point Google Wifi mesh system with the primary Wifi point's WAN port connected to one of the four LAN ports on a Pace 5268AC Router (AT&T ISP). The remaining three 5268AC LAN ports are not connected and its WiFi is turned off. The primary Google Wifi

Hi all, I have read nearly every answer to this issue and cannot get my airport express to work. I am novice when it comes to this so I know my basics. I cannot find this bypass mode, bridge mode, or see my router listed on the available devices. All I have is some suit-iphone, unknown(and a bunch o

I had AT&T Fiber installed last week and have been having slow speeds. I'm using a Linksys EA9300 in DMZ Plus mode behind the RG (Pace 5268AC) and turned off IPV6 on the Gateway. On a 5GHZ network from the Linksys, I am only getting around 75-80 Mbps. If I connect to the AT&T Wifi on 5GHZ, I get 300

New subscriber with 5268AC RG. Connection drops every 10 minutes, I experience 100% packet loss. I am monitoring with PingPlotter Pro to 5 different external IPs and they all drop for about 15/20 seconds. Creating all kinds of havoc on my connection reliability. Any ideas of what to do or try?

5268ac Router, 1 or more AT&T smart WiFi extenders, smart home manager app Careful study of the info on the 5268ac router and the smart home manager app...Apparently the 5268ac router no longer reports a signal strength for devices when they connect to the WiFi via an extender.  This was easily test

How can I prevent the Pace 5268AC router from assigning my Linksys EA9500 router a static IP address? You have to use DHCP in order to set this router in the DMZ plus zone.   This worked up until the other night.  I came home and the AT&T Fast Fiber service was down.  After tro

I have a Vita lap top, I know its old, my last router, that connected fine, had issues and at&t replaced it. Now the new 5268ac router will not connect to the internet over wifi.Got a few frustrating days into this and it will not connect. It shows the wifi signal as hot. (Wired connection between r

Hello. This might be more of a Microsoft question but someone here may have experienced the same issue.YEARS ago I had a Linux server (I wanted to learn Linux) with 2 nics in it.  I was having an issue with the RG not seeing all the static IPs I had assigned to the nics - multiple IPs per nic.  I fo

After all kinds of problems, I had my old modem replaced with the 5268AC. I've had to remove my Apple WiFi Network and use the ATT router's WiFi. I can't get programs and music to play on my Apple TVs on this 5268 WiFi network if they are sitting on my NAS. If I replace it with the Apple one, they a

I maintain a Remote Desktop Connection to my computer at home (AT&T Fiber Internet) from work, due to the fact that I don't want any personal information on my work computer.  This Remote Desktop Connection was solid while I had cable internet service, but since I switched to AT&T Fiber Internet ser

I just got AT&T Gigapower (1 Gbps) installed and have run across a baffling situation. I have the Pace 5268ac Gateway and an Asus RT-3100AC router. On both devices, I get LAN speeds of 600+ Mbps up and down. On Wifi, BOTH devices (tested independantly of each other) test out at no more than 150 Mbps

I was sent a new RG model 5268AC to replace NVG599 which is now 3 years old. Phone rep said issues causing intermittent internet loss most likely caused because old modem. She said modem is supposed to be replaced every (2) two years? Is that true? Anyway, after installing the new modem I can not ge

I have a Pace 5268AC gateway that the Broadband 2 light is blinking red. Occasionally,  it will go solid green. As for as I can tell, all my services are working okay but the red light is really annoying. I called tech support who had me reset everything which was lengthy and a real pain to pair eve

I have a 5268AC modem/router. I have a Chromecast 2 set up, and primarily use it from my phone (HTC One M8) to control it. My phone connects automatically to the 5GHz spectrum, and when it's there, it can't see or talk to my chromecast. When I force the phone into 2.4GHz mode, it works just fine, bu

Hi All,  I just signed up for Uverse and got a 5268AC / Pace 5268AC included.  I have three internet savvy children, each with multiple devices and want to use a service or piece of hardware to be able to set up access times, controls and on/off switches for their individual devices (iPhones, iPads,

Just trying to figure out what services (i.e. Netbios, NNTP, H323,telnet, etc.)    I can block in the PACE 5268AC router without affecting the DirectTV receivers / satellite Dish, etc. connected to the router.

I've got the 5 usable statics. I use a linux server to act as my router.  The linux server is also a web and mail server plus some other services.   I've configured the 5268ac to put the linux server in dmzplus mode so it should be open in and out.  Everything has been working but

I have fiber on the Pace 5268AC FXN and I connected my cisco rv325 router and put it in the DMZ+ on the Pace modem (since you can't bridge directly).  My cisco is showing the external ip on the wan port.  My problem is that I can ping the external address from outside and I want that to be blocked.