Teacher
•
3 Messages
How to dereigster an orphaned EL52203 handset to be able to register with my base
Hi - I purchased an orphaned EL52203 handset to replace a damaged handset on my new system (one damaged, the other is OK). What is the reset or deregistration key sequence needed to put the orphaned handset into registration mode?
Accepted Solution
Official Solution
Phonesludgdad
Teacher
•
3 Messages
4年前
Success! - yes, the video you linked worked (the key being entering *7890# while in settings). I've written the process down here for others:
How to reset/deregister an EL50003-family handset to re-register with base.
For here: M/S = menu / select button (upper right)
1) M/S, scroll to SETTINGS, M/S
2) Enter *7890#
3) Scroll to TEST HANDSET, M/S
4) Scroll to NEXT PAGE . . ., M/S
5) Select REGISTER CLEAR, M/S, M/S
6) Display shows OK meaning successfully reset.
7) Use OFF button to get back to main display which will flash “to register HS...”.
😎 Place on base, will say Registered after 15 sec or so.
Source: https://www.youtube.com/watch?v=NCHSuoOzDMQ
1
spoom2
ACE - Master
•
16.1K Messages
4年前
This works on many different makes and models of cordless handsets.
At the handset(s) do the following
*331734# followed by menu/select
The phone beeps twice, reboots and then comes back up ready to register to a new base station.
Registering to the new base station is now accomplished using the standard instructions.
3
Phonesludgdad
Teacher
•
3 Messages
4年前
Sadly does not seem to work for these - tried multiple times.
0
0
spoom2
ACE - Master
•
16.1K Messages
4年前
You're the first to say it didn't work, so all you can do is start searching the Internet. I did find a video here that uses a different sequence that may work. Just in case you missed it you did put a star * prior to the numbers, correct?
0
spoom2
ACE - Master
•
16.1K Messages
4年前
Thank you for posting the steps, I'll bookmark this one.
0
0
Jskyy1127
Tutor
•
4 Messages
4年前
Need info on model EL52301, no response pressing menu/select.
0
0
Rader002
Contributor
•
2 Messages
3年前
I've gone through the steps to deregister my new handset twice and it is still giving me the "out of range or no power at base" message.
I'm trying to pair a replacement el52300 handset and base with an el52400 system.
I've also tried the *331734# but when I press the m/s button the phone doesn't beep and says "edit number"
Any help would be much appreciated.
0
0
spoom2
ACE - Master
•
16.1K Messages
3年前
What handset and did you check to see if the two were compatible?
2
0
Rader002
Contributor
•
2 Messages
3年前
@spoom2 The new phone is Model el52300 (what it says under the battery cover) and trying to pair it with the el52400 system. When I looked it up on the AT&T website for compatibility it says the page is no longer available. When I look up both phone systems user manuals I get the same exact one so I'm guessing they are compatible. Also, both phones look exactly alike.
*I was able to get the phone to work. Unplugged the battery and plugged it back in. Instantly was able to register to my phone system.
1
0
rjsfl369
New Member
•
2 Messages
2年前
For spoom2:
Many thanks for all your help. The *331734# code worked fine for 2 handsets I had bought separately for an "ancient" SL 81028 series set. AT&T led us back to you, so don't leave the country!
Thanks again,
Roger
0
0
unknownme
New Member
•
2 Messages
2年前
The method given above, "*331734# followed by menu/select" worked to allow me to register a used phone I bought to add to my system.
Thank you.
0
0
tehevanthomas
New Member
•
1 Message
1年前
I have a VTech CS5119-2. One handset mysteriously started showing "Out of Range or no pwr at base". A combination of the techniques and codes above worked for me. Consolidated below:
Press Menu/Select,
Scroll to Settings,
Press Menu/Select,
Then *331734#.
The display shows: "Reg Clear"
Press Menu/Select.
Then the phone was deregistered, I placed it back on the base and it re-registered automatically just fine.
Thanks to the many contributors that helped me and others to get here. Hope this combination works for others.
0
0
Guercini
New Member
•
5 Messages
10分前
When you were getting the message "Out of Range or no pwr at base" did you press Menu/Select on the HS or the base. In my case when I press any button on the HS nothing happens and I keep seeing the "Out of Range or no pwr at base" on the screen. Thanks.
0
0
spoom2
ACE - Master
•
16.1K Messages
10分前
@Guercini Use the link I provided in the topic you started found here it provides several proven ways to force a deregister of a handset.
0
0
spoom2
ACE - Master
•
16.1K Messages
10分前
Locking this topic to further posting, we've consolidated all these different methods to deregister handsets into one topic which can be found here, deregister cordless handsets
(edited)
0
0