
Expert
•
14.5K Messages
U-verse Issue
Instead of offering my help, I'm asking for help from the knowledgeable people on this forum!
I'm having an issue with my U-verse service. The issue began the day after I received the new firmware update ((6.3.7.42) on my 3800HGV-B RG about 2 weeks ago. This may be a coincidence or the reason for the problem. Since receiving the new firmware update, I will lose all U-verse services (TV, internet and voice) approximately 18 - 22 hours after the last time the RG was rebooted. The only way to restore service is by rebooting the RG. Then the pattern continues of losing service 18 - 22 hours later and the RG needing to be rebooted to restore service.
I contacted Tier 1 Technical Support about the problem last week. The TSR ran tests on my line, noticed some errors, and dispatched a tech. The tech arrived on site and mentioned that there were some errors on the line; however, they should not be enough to take down my service. He did replace my 3800HGV-B RG with another 3800HGV-B which also has the new firmware update. He also opened a ticket for an I&R tech to come out to check my line. True to form, I lost service again about 20 hours after my RG was replaced, and I had to reboot the new RG to restore service.
The next day, the I&R tech arrived, tested the outside line and discovered some errors on that line. He replaced the line running from the NID to the pedestal. As I could have predicted, 22 hours after the I&R tech left, I lost services again requiring a reboot of the RG to restore.
This patterned has continued since it started almost 2 weeks ago after my old RG was updated with the new firmware up. During the time that the service is up and running, I am having no issue with TV, internet or phone. All service work very well during that time. Also, when I do lose service, all the lights on the RG remain green. None of them begin to flash red which is a bit odd.
Contacting Tier 1 again on this issue would probably not be productive, so my next step will be to reach out to David's group. Before I do, I want to get some feedback from you guys. Is anyone else having this issue? Is it related to the new firmware update, or is that just a coincidence?
Also, here are my screenshots from UVT:
3 Attachments
texasguy37
Expert
•
14.5K Messages
12 years ago
The factory reset of the RG is holding down the small reset button in the back of the unit for about 20-30 seconds.
0
0
hpmsrm
Master
•
5.7K Messages
12 years ago
OK, T.G. Thankyou.
We have not experienced the same problems with our RG since the upgrade. BUT.....recently, on three or four occasions....late at night(like after 1 or 2 AM) we have experienced total loss of channel 1210. I get the message on the screen reporting loss of signal and all the suggested trouble shooting moves. Other channels are OK. Just the one channel disappears.....sometimes for 5 minutes....sometimes for as much as a 1/2 hour. Everything else works fine. I think it must be a problem at the program source. The HD channel 210 does not suffer this malady. This is a fairly recent problem. Always the same. Just the one channel goes dead for a period of time. This doesn't sound anything like your problem....at least not to me.
0
0
Shyster951
Scholar
•
222 Messages
12 years ago
I assume so, but I did not check the 'old' RG that was replaced on 10/19 for what firmware version it was running at the time we suddenly began to have loss of service first noted 10/17.
However, the onset of the problems with my service roughly correspond to when yours began, AND the new RG has the same firmware version as does yours now, and was experiencing the same loss of service until the Prem Tech rewired my NID as previously described.
0
0
texasguy37
Expert
•
14.5K Messages
12 years ago
Thanks for the info.
0
0
Shyster951
Scholar
•
222 Messages
12 years ago
No problem. In the process of this I've gone from 'Senior Newbie' to 'Junior Ninja'... Wooo Hooo!
0
0
texasguy37
Expert
•
14.5K Messages
12 years ago
Congrats!
0
0
Shyster951
Scholar
•
222 Messages
12 years ago
Sorry to say that after being up since last Friday, i returned home to no TV, Uverse phone or internet. Rebooting the RG brought it all back up, for how long remains to be seen.
Guess I'll call back the same Prem Tech to see what he has to propose this time.
0
0
texasguy37
Expert
•
14.5K Messages
12 years ago
I am now working through my issue with David's Group. I struck out with all of my troubleshooting steps. The problem continues!
0
0
RCSMG
Expert
•
23.3K Messages
12 years ago
If you can't reach the prem tech come back here and click on the hyperlink in my sig. You will be taken to David's contact info. Sned him an email with your info and he or a member of his staff will be in touch with you.
0
0
texasguy37
Expert
•
14.5K Messages
12 years ago
I had another tech onsite today as a result of working with David's group. He replaced the 3800HGV-B RG with a 3801HGV RG and replaced the battery backup. I have posted new screenshots from the 3801HGV RG below. I noticed a dramatic reduction in the Noise Margin and the Power Level along with changes in the Bitloading graph compared to my previous post.
0
0