3G Microcell - 3G Red Light Flashing

I have had it where the 3G light is flashing red and I still have a signal.  It usually fails after that.

Mine is currently solid green.

It lost its Internet signal, yesterday (the modem took a short break).  It flashed green (and I had no signal) for about 20 minutes and went solid green and I had a connection.

BTW...  I woke up a flashing red light and no connection.  Turned off for 30 seconds before I left for work.  Green when I got home.

I have found the reason why my ATT microcell 3G bars blink red.  I am not sure if this is everybody's issue, but it certainly is mine.

If my microcell is connected to a Gigabit Ethernet (GbE or 1 GigE) network, i get the flashing 3G bars after a reboot.

If I connect to a 100 Mbit/s network, all is good.

I basically had to convert my gigait ethernet network to 100Mbit using a 100Mbit switch.

Hope this helps.

So, I recently had same problem as everyone else > 3g red light flashing.  I reset both my router and modem and unplugged microcell.  For 24 hours after doing this, it worked.  Now, the 3g red light flash is back and NO MCELL!  My router is the Cisco E4200 and Modem is the Actiontech MI424.  I changed the MTU as referenced on line in an attempt to fix the problem.  No dice.  Is there a solution?  Or do I now own a door stop?

FWIW: I also am using the VZ network extender in my house as we are on VZ as well as at&t.  The VZ NW extender works and has worked from the begining.  So, I am no expert but the problem seems to be with Microcell. 

Same concept as AT&T Microcell but used on Verizon network.  In my family, I am only one on VZ.  Wife/kids on AT&T.  My VZ extender has worked from the start.  Microcell, not so much.  Since my post, I reset modem/router twice and so far (since Sunday) I have MCell.  IDK, I hold my breath and check the front of the Microcell daily to ensure 3g is green.  

Just waiting until the iPhone 5 is released so i can get off ATT and this microcell.  Wonder if VZ will throw in an extender to switch.

spoke too soon.. back to flashing red 3g on microcell.  Is there a fix?

---

@Otto Pylot wrote:
I believe there's a little reset button (hole) on the back of the MicroCell. You might want to try that. I think you hold it in for 10 seconds but you may want to consult the instructions first just to make sure. For me, all I had to do was power cycle and the flashing red 3G light went back to green and has stayed there ever since. I think one of the reasons that VZs work better is that they are on a different technology which may make it more agreeable to signal booster/extenders than AT&T. Maybe less interference?

---

Wasn't there a long discussion a few months back about how pushing the reset button would "brick" the device?

---

@overclockedpc wrote:

I also have had the flashing 3g light problem for a while and I MAY have come up with some kind of fix but need someone to help me test it. 

 

So, if your microcell is flahing a red 3g light, please try the following and let me know what happens.

 

1) With the microcell flashing red, unplug the ethernet cable while leaving power plugged in.

2) Wait 2 mnutes, unplug power cable.(whileethernet is unplugged).

3) Wait 30 seconds, plug power cable in with ethernet cable unplugged.

4) Wait 2 minutes, plug in ethernet cable. (while microcell is powered on)

5) Wait 2 minutes, unplug power cable (leaving ethernet plugged in).

6) Wait 30 seconds, plug in power cable. (with ethernet cable plugged in).

 

This should clear the red 3g light.  If it does not, try power cycling again (unplug power, wait 30 seconds and plug back in).

 

If anyone is dealing with the red 3g light issue and can try this, please report back and let us know if it works or not.  AT&T support is clueless on this issue, but maybe we can help each other find a solution.

 

Thanks for everyone's help in testing this.

 

[Edited to comply with Guidelines]

---

---

@E the P wrote:

---

@Otto Pylot wrote:
I believe there's a little reset button (hole) on the back of the MicroCell. You might want to try that. I think you hold it in for 10 seconds but you may want to consult the instructions first just to make sure. For me, all I had to do was power cycle and the flashing red 3G light went back to green and has stayed there ever since. I think one of the reasons that VZs work better is that they are on a different technology which may make it more agreeable to signal booster/extenders than AT&T. Maybe less interference?

---

Wasn't there a long discussion a few months back about how pushing the reset button would "brick" the device?

---

I don't recal that discussion but I haven't read everything here. I've used the reset button a couple of times and never had any problems. Can't see why they would put a reset button on the back to only have it brick the MicroCell. It's not marked Service Only. It's marked reset.